About

Gender

Male


Location

Richmond, BC


About Me:

15 years of RC experience in airplane and heli. Into UAV and FPV 1 year ago.


Please tell us a bit about your UAV interest

Been flying Penguin and self assembled quad with APM2.5.2. Just bought Pixhawk for upgrade.


Hometown:

Hong Kong


Activity Feed

Frankie Fung replied to Cala's discussion Video streaming using UVC device in Tower (Droidplanner)
"Noted Tower disappears from Google play. Have briefly tried Mission Maker. Cala said:
Tower was stopped developing some time ago now, try with Mission Maker, its a remake, if you have better luck."
Feb 18, 2019
Frankie Fung replied to Cala's discussion Video streaming using UVC device in Tower (Droidplanner)
"Bernardo said:
Still no advance here:
When I connect the video Rx module to the tablet running Tower, the program (Tower) goes off.
Also, it is not possible (no signal or black screen) to run the Tower app showing video screen
and flight data on…"
Feb 15, 2019
Frankie Fung replied to Cala's discussion Video streaming using UVC device in Tower (Droidplanner)
"Bernardo said:
Still no advance here:
When I connect the video Rx module to the tablet running Tower, the program (Tower) goes off.
Also, it is not possible (no signal or black screen) to run the Tower app showing video screen
and flight data on…"
Feb 15, 2019
Frankie Fung posted a discussion
I have a helical antenna made by my friend.In directional antenna, do we distinguish between left hand or right hand circular polarization ?Please confirm the antenna in the attached photo is LEFT hand circular polarization.
Feb 14, 2019
Frankie Fung posted a discussion
Pls see attached screen capture on ardupilot firmware site.I want to run arduplane firmware on OpenPilot Revolution board. Have already installed driver and flashed STM32 bootloader to the board, which is recognised in the COM port in Mission…
Dec 13, 2018
Frankie Fung posted a discussion
Before the problemYesterday I configured a APM2.6 to plane. Everything was fine, gyro works, 6 flight modes were programmed in Tx and work, GPS also works, among other things.ProblemSecond day into bench testing, when toggling the flight mode switch…
Dec 11, 2018
Frankie Fung replied to Marcin Kordi's discussion Arducopter V3.5.5 Traditional heli althold problem
"Hi Marcin,
Did you get help feom anybody ? I have the same problem. When switching from stabilize to alt hold, the collective pitch decreases by 3-5 degrees.
I searched all the parameters in Mission Planner, but can't find a relevant parameter. My…"
Sep 21, 2018
Frankie Fung posted a discussion
I download the Dataflash log via Mavlink in MP. The Log Downloader window opens. But the log file dates shown next to the files are always 31/12/1969 4:00:00 pm .Is there a way to change the date so it automatically reflects the date when the files…
Mar 28, 2017
Frankie Fung posted a discussion
 I am running Minim OSD V1.0 on ArduplaneV3.2.3. Power supply to OSD is 2 stages, ie. 12V to video side and 5V from APM2.6. OSD firmware is R800, Char set 2.4.0.2 mcmAs soon as I arm the motor by pushing the rudder stick to the right, the flight…
Nov 24, 2016
Frankie Fung posted a discussion
I bought a V2.0 Minim OSD from the following source :--http://www.goodluckbuy.com/crius-mavlink-osd-v2-0-minimosd-compatib... had problem connecting the OSD to my PC via FTDI cable. Tried 2…
Nov 15, 2016
Frankie Fung replied to Andrea Longobardi's discussion Pixhawk 4 and EMAX BLHeli ESC
"I recently assembled a S500 quad with Pixhawk, and Emax 30A BLHeli firmware ESC. It took me a while to have all the 4 ESC calibrated using "All At Once " calibration. But when reducing the throttle to minimum, the motors on the right hand side…"
Nov 10, 2016
Frankie Fung replied to Frankie Fung's discussion Auto Analysis error message in Mission Planner
"I downloaded again from the link given in your second last email and still got 1.3.35.

 Pls advise when the latest version (1.3.37) will be added to the new server.

Thanks"
Mar 30, 2016
Frankie Fung replied to Frankie Fung's discussion Auto Analysis error message in Mission Planner
"Thanks for the support.
I tried the following link for the latest MP version :--
                               http://ardupilot.org/plane/docs/common-install-mission-planner.html
but still got version 1.3.35.
Could you please give me the link for…"
Mar 30, 2016
Frankie Fung replied to Frankie Fung's discussion Auto Analysis error message in Mission Planner
"Thanks for reply.

MP 1.3.35 build 1.1.5878.12941 which I am using is the latest version, I believe, as I checked for update in the HELP section of MP, and it came back saying there is no update.
Any other clue that you can suggest ?
Thank you."
Mar 29, 2016
Frankie Fung posted a discussion
I have been using Mission Planner for 2-3 years without problem. Recently, after downloading data flash log via Mavlink  and reviewing the log, I clicked the Auto Analysis button m and got the following error message :--                           …
Mar 29, 2016
Frankie Fung posted a discussion
I have been running Mission Planner trouble-free for over 2 years without problem on my desktop PC. Until 2 days ago, when I was messing around trying to install the driver for PX4FLOW on the PC, i tried many different ways, without…
Dec 5, 2015
More…