Gender
Male
About
About Me:
MK user
Please tell us a bit about your UAV interest
I like to know how to build an autopilot
Hometown:
Tel Aviv
Activity Feed
"If I got u right , when you use Xbee s1 with sparkfun regulated board v13, it worked like a charm?"
"what kind of autopilot are you using?"
"I noticed the pitch drift on first arm , both on pixhawk , and apm , and from ver 3.2 , 3.2.1 , to 3.3.dev
have any of you noticed it? is it predictable behaviour ?
should I expect a small drift after arm ( I mean , when the board sits at the table…"
have any of you noticed it? is it predictable behaviour ?
should I expect a small drift after arm ( I mean , when the board sits at the table…"
"Hi ,
I have Mission Planner 1.3.11 ,and in the help it says geotiff support,
then how do I use it?
all the best
Itay"
I have Mission Planner 1.3.11 ,and in the help it says geotiff support,
then how do I use it?
all the best
Itay"
"Hi , two questions
1. how to copy the qml folder to the debug folder.
2. is there support for joystick ? I can see it in the MainWIndow.ui , but it seems to be disabled.
thanks
Itay"
1. how to copy the qml folder to the debug folder.
2. is there support for joystick ? I can see it in the MainWIndow.ui , but it seems to be disabled.
thanks
Itay"
"Hi,
I cannot see the parameter I added using this explanation
http://dev.ardupilot.com/wiki/code-overview-adding-a-new-parameter/
although It compiles just fine !"
I cannot see the parameter I added using this explanation
http://dev.ardupilot.com/wiki/code-overview-adding-a-new-parameter/
although It compiles just fine !"
"have the same problem"
"HI, newbie problem !
I follow the instruction at:
http://dev.ardupilot.com/wiki/settraing-up-sitl-on-windows/
reached to the place I tries to run the autotest.py:
./Tools/autotest/autotest.py build.ArduCopter fly.ArduCopter logs.ArduCopter --map…"
I follow the instruction at:
http://dev.ardupilot.com/wiki/settraing-up-sitl-on-windows/
reached to the place I tries to run the autotest.py:
./Tools/autotest/autotest.py build.ArduCopter fly.ArduCopter logs.ArduCopter --map…"
"p.s.
I am using 0-5k resistors"
I am using 0-5k resistors"
HI, I am trying to add a small control joystick to apm 1 expansion ports.but I have some problems.I was able to put the code right and read the pots.but I noticed that the the volt on the control pins are NOT separated, meaning that one pot changes…
tried to addpot1_analog_source = hal.analogin->channel(AN6);pot2_analog_source = hal.analogin->channel(AN7);and then…
"Hi, I am trying to use expansion pins , and add external pot to calibrate internal variables.
I need an example how to use them in the 3.X code
any help?"
I need an example how to use them in the 3.X code
any help?"
"could you post the code you added to make the led works"
my APM1 doesn't want to init, I use it with ARMING_CHECK 0 so it will pass all the annoying checks, but he keeps on failing to initialize , any help
"rubbish ! - the market is not saturated at all , there are over priced ESC each piece cost about 80 dollar !!!
no one wants 200 amp , we need good and safe ESC that would do the job.
today the only good ESC are over priced !"
no one wants 200 amp , we need good and safe ESC that would do the job.
today the only good ESC are over priced !"
"Great project Jason,
I am a multirotor user, and I have a lot of tips to give u for multirotor use:
1. make it easy to install ! , most people attach it to a 10X10 mm aluminium square rod, make it easy to install ( also use as heat sink)
2. make it…"
I am a multirotor user, and I have a lot of tips to give u for multirotor use:
1. make it easy to install ! , most people attach it to a 10X10 mm aluminium square rod, make it easy to install ( also use as heat sink)
2. make it…"
