Gender
Male
About
Location
Bs AS
Activity Feed
"My Naza will unarm if sits on the floor for a few seconds. If you like to fly again you have to rearm.
Unless you want to fly missions were you land between waypoins, looks like a nice feature to have.
We dont do so many touch&go with copters, and I…"
Unless you want to fly missions were you land between waypoins, looks like a nice feature to have.
We dont do so many touch&go with copters, and I…"
"have any one seen this:
http://gadgetshow.channel5.com/gadget-show/blog/war-of-the-robots-t..."
http://gadgetshow.channel5.com/gadget-show/blog/war-of-the-robots-t..."
"ok :-)"
",22 long is about 4 grams x round. 100 rounds are 400grams + 1.6 kg for a sub machine gun is about 2kg.
2 kg is not that much for a quad.
Things are exploding when hitted in certain area and the recoil of the gun can be seen while the gun is…"
2 kg is not that much for a quad.
Things are exploding when hitted in certain area and the recoil of the gun can be seen while the gun is…"
"She is on the safe side, fitted with four airbags..."
"Hi Randy,
thanks for your answer.
Actually I have 2 problems with the MAG.
With the motors off, I do the calibration (from MP or Flying) and North is awfull off. Even worth is that (still with the motor off) y turn the copter around and…"
thanks for your answer.
Actually I have 2 problems with the MAG.
With the motors off, I do the calibration (from MP or Flying) and North is awfull off. Even worth is that (still with the motor off) y turn the copter around and…"
"Hi,
would it be possible to get a cable about 20cm to connect the APM2 and daughter board? It might be nice to have the possibility to have magnetometer away from magnetic fields and at the same time been able to correct desviation on the mag…"
would it be possible to get a cable about 20cm to connect the APM2 and daughter board? It might be nice to have the possibility to have magnetometer away from magnetic fields and at the same time been able to correct desviation on the mag…"
"Hi,
I have some problems with logging.
Some time is working, most the time not.
Usually I get following messages:
Init ArduCopter V2.6Free RAM: 2346FW Ver: 118----------------------------------------load_all took 7768usPress ENTER 3 times for…"
I have some problems with logging.
Some time is working, most the time not.
Usually I get following messages:
Init ArduCopter V2.6Free RAM: 2346FW Ver: 118----------------------------------------load_all took 7768usPress ENTER 3 times for…"
"@Chris,
I guess its time you find a better argument.
My APM 2 is grounded until 2.6 is released. Hope my best for this release or I will give up. Only problem I have is I wont llike to sell any one else a not working system, so I have to build…"
I guess its time you find a better argument.
My APM 2 is grounded until 2.6 is released. Hope my best for this release or I will give up. Only problem I have is I wont llike to sell any one else a not working system, so I have to build…"
"When will be DMP available!!!!
I still remember
When using the internal sensor fusion processor of the MPU-6000, more than half of the Atmega2560 processing capacity is free for new advanced features.
Or I bougth something that promised what can…"
I still remember
When using the internal sensor fusion processor of the MPU-6000, more than half of the Atmega2560 processing capacity is free for new advanced features.
Or I bougth something that promised what can…"
"@John,
follow Ruwan link an take a look at 0:28 !!!!
COOL!"
follow Ruwan link an take a look at 0:28 !!!!
COOL!"
"Hi,
were do I find the manual compass calibration mode in MP?
Regards,
Pablo"
were do I find the manual compass calibration mode in MP?
Regards,
Pablo"
"Hi,
were do I find the manual compass calibration mode in MP?
Regards,
Pablo"
were do I find the manual compass calibration mode in MP?
Regards,
Pablo"
"Would it be possible to have multiwii compiled for working with APM 2.0?
Of course a version without GPS, etc.
It very dificult to change all the time from one board to the other.
And for us using only stabilized right now might be a good way to…"
Of course a version without GPS, etc.
It very dificult to change all the time from one board to the other.
And for us using only stabilized right now might be a good way to…"
"Hi,
my APM 2 has turned my xcopter unflyable.
It was perfect with APM 1.
It start to drift dto one side and never stops.
I can compensate with stick input.
I have exchanged propeller position to see if it leans on other direction but not.
I have…"
my APM 2 has turned my xcopter unflyable.
It was perfect with APM 1.
It start to drift dto one side and never stops.
I can compensate with stick input.
I have exchanged propeller position to see if it leans on other direction but not.
I have…"
"Hi Sandro,
I dont think is a problem from FTDI or program used for loading the Firm/Charset.
As mentioned above after link is stablished with CGS it works perfectly.
Will try to connect TX pin from OSD and let you know.
Pablo"
I dont think is a problem from FTDI or program used for loading the Firm/Charset.
As mentioned above after link is stablished with CGS it works perfectly.
Will try to connect TX pin from OSD and let you know.
Pablo"
