About

Gender

Male


Location

Orihuela, Alicante


Please tell us a bit about your UAV interest

I want make a autonomous helicopter for filming (helicam) and now and Octocopter.


Hometown:

Orihuela


Activity Feed

Pablo Zeron replied to Randy's discussion ArduCopter-3.0.1 released!
"Hi,
Yesterday while I was filming some aerial footage for a commercial I crashed the octo, I was returning to land after a take when suddenly I lost control, at the same time I saw one motor stopping, and as I can't retake the control, I pull down…"
Jul 21, 2013
Pablo Zeron posted a discussion
Hi, I have made a small modification to the "AP_Mount" library to be used mainly by the filmmakers, basically is:1- Add a dead zone when we use the joystick mode to prevent undesired movements of cam, you can change the dead zone using the min and…
Mar 3, 2013
Pablo Zeron posted a blog post
 Hi, I have made a small modification to the "AP_Mount" library to be used mainly by the filmmakers, basically is:1- Add a dead zone when we use the joystick mode to prevent undesired movements of cam, you can change the dead zone using the min and…
Mar 2, 2013
Pablo Zeron replied to Randy's discussion ArduCopter 2.9 / 2.9.1 released
"Hi, Yesterday I crashed my octa testing "alt hold" mode with the new 2.9.1, with the parameters I was testing it seems to be stable.
While I'm testing this mode I had to reduce the throttle to correct altitude when suddenly the copter flips and hit…"
Feb 17, 2013
Pablo Zeron replied to Randy's discussion ArduCopter 2.9 / 2.9.1 released
"Hi,
Today I have made my first flight my homemade octocopter, and I have some issues:
1- Stabilize works great with stock values except in P that I have 0.90 because I use 400kv motors, but the copter starts to yaw slowly.

2- Alt hold not works as…"
Feb 4, 2013
Pablo Zeron replied to Rob_Lefebvre's discussion New Octo Copter Design/Build Thread
"Hi,
Here you have a lot of pictures of my camera gimbal:

Add-on for full pan:

Plate for light cameras:

Gimbal itself:




You can adjust GC with the fixed support or with the full pan add-on:


Detail of camera tray:

The dampered plate have an…"
Oct 31, 2012
Pablo Zeron replied to Rob_Lefebvre's discussion New Octo Copter Design/Build Thread
"Hi,This is my own design octo, It flies very stable with 2.7.3 version (stabilize mode and 0.090 P).
I use 6S Lipos (nano-tech) with Turnigy L5055A Motors (400kv), It have a width of 100cm shaft to shaft.
The frame is 3mm CF and the draw current is:…"
Oct 29, 2012
Pablo Zeron replied to Ruwan's discussion Share your drone info thread
"Here goes information about my octo.
Frame: Carbon Fiber Custom frame
Controller/autopilot: APM1
Esc: Redbrick 70A with simon FW (http://www.hobbyking.com/hobbyking/store/uh_viewitem.asp?idproduct=...)
Motors: Turnigy L5055 400Kv…"
Aug 5, 2012
Pablo Zeron replied to Duran - ALTI's discussion APM Octocopter Thread
"Hi,This is my heavy custom octo, don't fly yet, but I will do soon.It have a width of 100cm shaft to shaft and I will use 6s lipos with 400 kv motors.What do you thing about it? Any suggestions?Thanks.



P.D. Sorry for my english."
Aug 1, 2012
Pablo Zeron commented on Chris Anderson's blog post ArduPlane home page
"Is possible to use the LS20031 GPS receiver in binary or only in NMEA? Will it be supported in next revisions of APM? Thanks."
Sep 8, 2010
Pablo Zeron commented on Chris Anderson's blog post ArduPlane home page
"It's ok, but if I have understood it well (my english level isn't as good as I wish), using elevon mixing, you are lossing the elevator as itseft, making elevator as a mixing of the two alerons. With this code you can still use CH2 for Elevator and…"
Aug 31, 2010
Pablo Zeron commented on Chris Anderson's blog post ArduPlane home page
"Hi, I have tested today the APM + OILPAN with my Acromaster, and works great. Here is the source code with modifications to work with two aleron servos (CH1 & CH5). Good luck and thanks for APM.…"
Aug 31, 2010
Pablo Zeron replied to Rustom Jehangir's discussion Trouble reading inputs from receiver
"I made some test with my APM, when are connected signals from input 0 to 5 and power on the APM, if i disconnect any input (0 to 5) and connect it in the other two free inputs, i can't see any response in the terminal, but if a make a reset in the…"
Jul 4, 2010