Gender
Male
About
Please tell us a bit about your UAV interest
www.heliphoto.it
Activity Feed
"Hi Justas,
I had an RC predator from www.lindinger.at, it's 1600mm wingspan it's light, well done but very nervous model!!!
Forget 1kg of payload with this plane, my multiplex Easy Cub (1600mm wingspan) can lift with 500gr of payload.."
I had an RC predator from www.lindinger.at, it's 1600mm wingspan it's light, well done but very nervous model!!!
Forget 1kg of payload with this plane, my multiplex Easy Cub (1600mm wingspan) can lift with 500gr of payload.."
"I have a question: all photos are taken at the same altitude? I try sometime to do something similar but my first problem was that photos are taken at different altitude (i used an helicopter).
Somebody know a software that work with gps data to…"
Somebody know a software that work with gps data to…"
When you use FMA Co-Pilot CPD4 on a plane with 2 servos on wing (one for airelon) usually you must connect an Y cable to use correctly CPD4 stabilization.With this configuration you cant use the flaperon mix (it move the 2 wing servo to the same…
"This product was selled last year (a lot of EU shop and ebay shop) but now it's hard to find.
I know people that use it, it's accurate but they say FMA CPD4 is better.
An alternative is Futaba Pilot PA-2, but it can work with sun low at the…"
I know people that use it, it's accurate but they say FMA CPD4 is better.
An alternative is Futaba Pilot PA-2, but it can work with sun low at the…"
"So why dont insert on ardupilot a instruction to change the baudrate on startup?
On startup you can use 4800bps, send setup string to GPS and change Ardupilot bps to new value.
On next boot if GPS remember the fast bitrate the command run at 4800…"
On startup you can use 4800bps, send setup string to GPS and change Ardupilot bps to new value.
On next boot if GPS remember the fast bitrate the command run at 4800…"
"I'ts quite easy if you use an external Servo control board or relay (with pin levels).
Maybe you can add a field on waypoint array for action.."
Maybe you can add a field on waypoint array for action.."
"Check on Arduino site, for example you can use an Arduino diecimila board (without ATMEGA chip) as FTDI cable for Arduino mini (or for what u want because u have just to use +5, GND, TX, RX and RESET)
cheers"
cheers"
Hello,I write this post for who like me have an Arduino Mini USB Adapter and want to upload code (or burn bootloader) by ISP on ATMEGA168 or Attiny45.This is the connection schema from Mini USB (or any FTDI cable based on FT232RL chip, you can also…
"I know Chris, I just ordered a FTDI board from sparkfun.. but i suppose that on my Ardupilot there is some problem with bootloader. Maybe i try to burn a bootloader.."
"I use version 13, I ask just to know if i can try manual reset with early Arduino studio release."
"Look here:
http://arduino.cc/en/Main/MiniUSB
Can i try to connect DTR pinout of second figure to DTR on ArduPilot?
ArduPilot code is compatible wirh Arduino studio v.8? I ask that because on previous release software reset is not used. I can try…"
http://arduino.cc/en/Main/MiniUSB
Can i try to connect DTR pinout of second figure to DTR on ArduPilot?
ArduPilot code is compatible wirh Arduino studio v.8? I ask that because on previous release software reset is not used. I can try…"
"Hi Chris, thanks to the reply
There is a way to simulate reset line with my hardware?
I load the same code in the same way (i chenge board from diecimila to mini) on my arduino mini board and it work well (I use it for some test).
GPS not…"
There is a way to simulate reset line with my hardware?
I load the same code in the same way (i chenge board from diecimila to mini) on my arduino mini board and it work well (I use it for some test).
GPS not…"
"Hello,
I've some problem uploading arduino code.
This is my configuration:
- Ardupilot powered by external 5v connected on OUT1 servo slot
- FTDI cable (this one: http://www.arduino.cc/en/Main/MiniUSB ) that's work because i test it with an…"
I've some problem uploading arduino code.
This is my configuration:
- Ardupilot powered by external 5v connected on OUT1 servo slot
- FTDI cable (this one: http://www.arduino.cc/en/Main/MiniUSB ) that's work because i test it with an…"
"well i think that with high wind i dont fly :D
what's a good 4ch alternative??
We can make a plane cassific for UAV.. 3ch and 4 ch based on personal experience!"
what's a good 4ch alternative??
We can make a plane cassific for UAV.. 3ch and 4 ch based on personal experience!"
"Sorry, I've read the Ardupilot 2.0 post after.. :D"
"The FMA sensor will be sold as spare?"
