Gender
Male
About
Please tell us a bit about your UAV interest
Amateur
Hometown:
Brisbane
Activity Feed
G'day all I'm really hoping some jet here can help me sort out an issue i have when helping a buddy and something I've faced previously in my own projects and not been able to resolve.I am assisting a fellow flyer to setup an APM running the latest…
"Gday Tom,
Yeah. I'm pretty ken on checking surface area controls and so on prior to launch so it became pretty apparent pretty qucikly something was not right. I had it it all up with the ESC +ve pin connected but after testing removed it thinking…"
Yeah. I'm pretty ken on checking surface area controls and so on prior to launch so it became pretty apparent pretty qucikly something was not right. I had it it all up with the ESC +ve pin connected but after testing removed it thinking…"
SKTHKPilot - Connected 3DR Power Module and ESC/SBEC power?I've found that when powering a HK Pilot off a 3DR Power Module alone, it will boot ok but as soon as I move a servo the HKP goes into a reboot loop. Uncool. I'd rather just power the HKP…
"No worries. I'm in Brissy. Prob just my setup."
"Ok cheers.
I'll just ask is this something you'll be able to resolve and in 'about an hour' would be likely when it would be resolved or do you mean in general?
I only as because I have been getting this error for atleast a week so I was starting…"
I'll just ask is this something you'll be able to resolve and in 'about an hour' would be likely when it would be resolved or do you mean in general?
I only as because I have been getting this error for atleast a week so I was starting…"
Gday for some reason when I try to retrieve 'Old Firmware Versions' I get an error (see attached screen cap). I had gotten a previous version a little while ago then all of a sudden I cant. The reason I want an older version is that anything above…
"Id suggest you are right mate. I'm writing this from work and that number jumped to mind. I am certain I am running sub 3.0.X.
Had to be Arduplane atleast, or the flight wouldnt have gone as well as it did.
Thx."
Had to be Arduplane atleast, or the flight wouldnt have gone as well as it did.
Thx."
Gday I'm hoping someone can help isolate an intermittent issue I'm trying to nut out. I'm running firmware 2.9.1 on a Arduflyer 2.5 in a fixed wing platform with a MinimOSD v0.1. I'm running below 3.0.x because anything over that will cause a 'Bad…
"Thx Mike. I fiddled with the curve settings and found a suitable setup so all good. Thx for a baseline to work from."
"That's pretty awesome Mike, thx for such a simple tut. I've spent all my APM time on a DX7s and am really new to 9XR but info like yours is of great value.
I wonder is it possible to change the left switch to always override to RTL instead of…"
I wonder is it possible to change the left switch to always override to RTL instead of…"
"I should add that it is quite a manouverable tricopter and very responsive. Ive add a little expo here and there just to soften it when doing HD filming flights."
Gday, Just startng to get to know my apm tricopter after a few months, a mate pretty much set it up ardu wise and taught me as much as I could grasp, which is enought to keep it safe for now. He set it up pretty docile and soft which is how I liked…
"@MegaFlare
No probs. Very happy to help out in the little ways I can."
No probs. Very happy to help out in the little ways I can."
"@MegaFlare.....
I'm sure if I'm getting what you are saying but maybe when you are trying to change the numbers maybe try moving the Gear switch. Again not sure if you've tried it. Maybe just try again."
I'm sure if I'm getting what you are saying but maybe when you are trying to change the numbers maybe try moving the Gear switch. Again not sure if you've tried it. Maybe just try again."
"Fabian I set my DX7s just as you have and it works a treat. Switch the GER and AUX1 in the mix setup and changed to you numbers. I only really get 5 but all I wanted was RTL, Stab and Loiter, which I now have thx to you and Bruce. Cheers guys."
"I should also mention I am using Arduplane so my APM input channel is 8.
I dont get why this isnt working for me. I have Aux1 on the RC Rx cabled to APM input 8, its giving me 3 modes off the Flap switch. I have followed the steps above so precisly…"
I dont get why this isnt working for me. I have Aux1 on the RC Rx cabled to APM input 8, its giving me 3 modes off the Flap switch. I have followed the steps above so precisly…"
