About

Gender

Male


Location

kerala


About Me:

Robotic enthusiast


Please tell us a bit about your UAV interest

Interested in ground rovers


Hometown:

Kollam


Activity Feed

Varunlal V replied to Ben's discussion Any modification should be made to apm 2.6 with brush ESC? in ArduRover User Group
"IWP_20160215_001 - Cop y.jpg"
Feb 15, 2016
Varunlal V replied to Ben's discussion Any modification should be made to apm 2.6 with brush ESC? in ArduRover User Group
"I want to drive two motors per side using one ESC, motor is 300mA, but for testing i had connected only one.
yes, motor is connected while getting hot....(Though motor is connected, its actually not turning, leds in the esc is on)
used CLI, just to…"
Feb 13, 2016
Varunlal V replied to Ben's discussion Any modification should be made to apm 2.6 with brush ESC? in ArduRover User Group
"My terminal looks like this "
Feb 13, 2016
Varunlal V replied to Ben's discussion Any modification should be made to apm 2.6 with brush ESC? in ArduRover User Group
"Navigation controller APM 2.6 with Mission planner 1.3.34
firmware version (Dont know how to check)
ESC is china make
http://www.ebay.com/itm/RC-ESC-20A-Brush-Motor-Speed-Controller-w-B..."
Feb 13, 2016
Varunlal V replied to Ben's discussion Any modification should be made to apm 2.6 with brush ESC? in ArduRover User Group
" my brushed esc getting hot when connected with ardupilot board, but is working well with a chinese servo tester, motor spins both sides and stops also with the servo tester and no heating also, what can be the problem?"
Feb 13, 2016
Varunlal V replied to Richard Boyhan's discussion ESC Getting Really HOT
" my brushed esc getting hot when connected with ardupilot board, but is working well with a chinese servo tester, motor spins both sides and stops also with the servo tester and no heating also
what can be the problem?"
Feb 13, 2016
Varunlal V posted a discussion in ArduRover User Group
My Brushed esc getting hot when connected to arducopter board,But its working smooth with the servo tester and motor run both direction and stops so all fine when tested with servo testerwhen esc connected, telemetry module not working, when…
Feb 11, 2016
Varunlal V posted a discussion in ArduRover User Group
can we control the brushed motors using brused esc such that, if we want to reverse the rover, then can we rotate the parallel motors in opposite direction?
Feb 9, 2016
Varunlal V replied to Varunlal V's discussion Ardurover 2.6 with Hbridge to control dc motors in ArduRover User Group
"In APM rover where we can give the input power? didnt able to get the input power pins

can we  connect a regular 6V, lead acid battery instead of lipo?"
Nov 9, 2015
Varunlal V posted a discussion in ArduRover User Group
can we use Ardurover 2.6 with Hbridge to control dc motors?is there any output to control enable direction and pwm pins from ardurover to control the respective pins of hbridge like l298?
Oct 26, 2015
Varunlal V posted a discussion
can we use Ardurover 2.6 with Hbridge to control dc motors?is there any output to control enable direction and pwm pins from ardurover to control the respective pins of hbridge like l298?
Oct 25, 2015
Varunlal V posted a discussion in ArduRover User Group
I am newbie to this forum and ardurover, I would like to build Ardurover using arduino mega 2560 board, where can i get that wiki, like the pins to connect the Hbridge, gps etc/
Oct 20, 2015
Varunlal V posted a discussion
I like to build Ardurover using arduino mega 2560 board, from where i can get the schematic for pins used for connecting Hbridge, GPS and configuration in the code etc?
Oct 20, 2015