Please tell us a bit about your UAV interest
film documentation
About
Hometown:
Bielefeld
Activity Feed
"hi,
auvida s e12 also operate with linux. currently i hope that it is possible to crate an fifo based pipe to netcat or socat directly from the h264 encoded video data stream. by default the e12 stream via rtsp and also http protocol. here are the…"
auvida s e12 also operate with linux. currently i hope that it is possible to crate an fifo based pipe to netcat or socat directly from the h264 encoded video data stream. by default the e12 stream via rtsp and also http protocol. here are the…"
"currently i don not test the b101 much more. i am still waiting a little bit more. if looks that software(firmware and maybe kernel driver) for the b101(Toshiba TC358743XBG bridge) is currently under develop.…"
"the gimbal on is an raspi. bit thr tp-link also act with the odroid c1"
"yes it act as normal wifi dongle. no driver needed. i am on kernel 3.4.1."
"hi paul,
the tp-link is only installed for testing. i do not use wifi broadcast on my gimbal. later i need an bidirektional setup."
the tp-link is only installed for testing. i do not use wifi broadcast on my gimbal. later i need an bidirektional setup."
"hi,
i have one since a few days and test it witch an netcat pipe with and without fifo file pipe. the latency is dependend to your network quality and your software (i use mplayer) at rx side the same with an attached raspicam module at 1080p 30fps.…"
i have one since a few days and test it witch an netcat pipe with and without fifo file pipe. the latency is dependend to your network quality and your software (i use mplayer) at rx side the same with an attached raspicam module at 1080p 30fps.…"
"this is an old opentx bug also in 2.0.13-17. minute beep settings are ignored and allays on.
/g
wolke"
/g
wolke"
"my general tip for save flying,
* NEVER NEVER NEVER trust gps and barometer!!
* never fly take-of ore land in some auto mode if you can not do this also for sure manually. you must stay tuned to recover the vehicle in each situation while auto…"
* NEVER NEVER NEVER trust gps and barometer!!
* never fly take-of ore land in some auto mode if you can not do this also for sure manually. you must stay tuned to recover the vehicle in each situation while auto…"
"aha,
please can you create an issue with your suggestion. since i while i also contribute to clonney and stop develop on my fork.
only to know. if i create the wolkstein fork, Wh display was one of the key resource there. because in conjunction with…"
please can you create an issue with your suggestion. since i while i also contribute to clonney and stop develop on my fork.
only to know. if i create the wolkstein fork, Wh display was one of the key resource there. because in conjunction with…"
"i know, why do you not simply change this in your lus script? you only have to remove wh on your display an than move the myh a litte bit to right. than you are fine:).
."
."
"hi,
to point one,
why not simple use an smaller cmin font on your script and create a new line for mah? i am at least a fan from wh. this is a real value to measure consumed ernergie. mah say absolute nothing about consumption. so it is only an…"
to point one,
why not simple use an smaller cmin font on your script and create a new line for mah? i am at least a fan from wh. this is a real value to measure consumed ernergie. mah say absolute nothing about consumption. so it is only an…"
"yes and no!
it work also on arduino pro mini and teensy2. but you need software serial on one message bus. also parsing severity messages is limited because less memory on pro mini and teensy < 3 boards.
/g
wolke "
it work also on arduino pro mini and teensy2. but you need software serial on one message bus. also parsing severity messages is limited because less memory on pro mini and teensy < 3 boards.
/g
wolke "
"Hi all,
currently some of later involved developers create an collaboration on github to improve the project and make it available for opentx2.1.x. and also apm3.3. in moment we work on porting to opentx2.1.x. apm3.3 improvements will follow. for…"
currently some of later involved developers create an collaboration on github to improve the project and make it available for opentx2.1.x. and also apm3.3. in moment we work on porting to opentx2.1.x. apm3.3 improvements will follow. for…"
"this branch is under development. also devs are on trail and error with 2.1. so this is why there is no clear set-up information at this state of development.
if you need stable telemetry on apm please use opentx 2.0.17 and the main s-c-l-v-rc…"
if you need stable telemetry on apm please use opentx 2.0.17 and the main s-c-l-v-rc…"
"@Clooney,
i currently follow the big progress on your fork. also on the lua side:). so i decide to discontinue my fork. this makes no sense any more and will confuse users. i change my readme.md shortly to "discontinued" and link to your fork…"
i currently follow the big progress on your fork. also on the lua side:). so i decide to discontinue my fork. this makes no sense any more and will confuse users. i change my readme.md shortly to "discontinued" and link to your fork…"
"thx for clearing this,
on your GW5100 did you test the Mini PCIe wifi card which they offered? did it work in wifibroadcast mode?
/g
wolke"
on your GW5100 did you test the Mini PCIe wifi card which they offered? did it work in wifibroadcast mode?
/g
wolke"
