About

About Me:

Electronic engineer.


Please tell us a bit about your UAV interest

Just an expensive hobby


Hometown:

Shipston on Stour


Activity Feed

charlie Soppelsa commented on OzCaGrr's blog post My first Blog post on DIY Drones!
"I don't want to be a killjoy, but in the UK we are limited to 400ft altitude, I assume you have similar laws. Flying FPV at your altitude is Dangerous and irresponsible. This sort of action will get FPV banned for all of us."
Nov 4, 2011
charlie Soppelsa posted a discussion
HiI have a ACM with a Mega 1.4 (1280) controller + oilpan, with GPS, Sonar, Magnetometer HMC5883 and a unused Mega 1.4 (2560) controller and 1 spare sonar for sale as a package. Offers around £200.00 the lot. Prefer to sell in UK, can demonstrate.
Oct 27, 2011
charlie Soppelsa commented on charlie Soppelsa's blog post Tricopter video
"Screenshot for the PIDs, motors are MK3638."
Oct 23, 2011
charlie Soppelsa posted a blog post
Here's a video of my tricopter. First attempt at some editing so it's a bit rough and it's got a bit jumpy in translation. Specification:14x4.7" APC props on 750mm centres, AUW 1700grm. Battery 4S 5A. flight time about 20 mins. ACM running…
Oct 21, 2011
charlie Soppelsa posted a discussion
The Tricopter yaw problem has been on the forum for months, and as fas as I can see it has not been resolved. There is a massive deadband on the yaw servo so that yaw control is like slamming a barn door, smooth control is impossible. A solution was…
Oct 13, 2011
charlie Soppelsa commented on charlie Soppelsa's blog post Low Voltage warning LEDS
"mm2, I take Sebastians point, although it's not that simple for people unfamiliar with software hacks and Mosfets, buffering etc and just want a simple plug and play unit. Don't forget, lots of Multirotors don't have the benefits of a ACM. So I'm…"
Oct 9, 2011
charlie Soppelsa commented on charlie Soppelsa's blog post Low Voltage warning LEDS
"I by my LED strips in the UK from Robotbirds or Giantcod, about £10 metre."
Oct 6, 2011
charlie Soppelsa posted a blog post
http://vimeo.com/30086732Untitled from charlie soppelsa on Vimeo.This little gizmo has saved my bacon on many occasions.  Multirotors tend to fall out of the sky with no warning if you let your lipo go flat. I use strip LEDs as navigation aids to…
Oct 5, 2011
charlie Soppelsa posted a discussion
Can I use programmers notepad to edit pde.files, I'm trying to change the deadband value in the radio.pde.
Sep 29, 2011
charlie Soppelsa posted a discussion
Hi I use a Canon Ixus 130 for HD Video on my Tricopter. Without any anti vibration measures the Video is a blurry mess, I've had to build a fairly elaborate camera mount to get rid of the vibration. The Antishake facility on the camera makes no…
Sep 19, 2011
charlie Soppelsa replied to charlie Soppelsa's discussion Tricopter Yaw Deadband
"Can anybody help with this ?"
Sep 4, 2011
charlie Soppelsa replied to Greg's discussion Motor Failure on First Flight
"Hi Greg
I've always used AXI motors they are the best but expensive, they are well made, reliable and efficient. However, I have recently switched over to Pulso motors, they are AXI rip-offs , they are equally well made and work exactly the same.…"
Sep 3, 2011
charlie Soppelsa posted discussions
Sep 2, 2011
charlie Soppelsa commented on Bob Hern's blog post Turnigy 9X IN STOCK at the US Warehouse!!
"I would be weary of the FrSky receiver, I used a 8 channel unit and FrSky tx unit in my Futaba T9CP. I had lots of  problems, flips and crashes. Investigating you could see the ACM outputs doing weird things. I went back to Futaba 35mHz and…"
Sep 2, 2011
charlie Soppelsa posted a discussion
I downloaded 2.0.39 TRI using the Mission planner, originally I thought the Accelerometers were not working. but now it seems that all accels and gyro's are reversed.From the Wiki the Tri configuration looking from the back is motor 1 front right,…
Aug 19, 2011
charlie Soppelsa replied to charlie Soppelsa's discussion NO ACCEL
"Forgot to mention, the Stab default pids are P=4.0 l=0.025 and Imax=1000 ? the Stab D value in the data settings column is 0 ?"
Aug 15, 2011
More…