Hi!
I hav an APM 2.5 with a 90A attopilot sensor. I am wondering if it is really necessary to connect gnd wire coming from attopilot sensor. The thing is I have the power jumper disconnected so I have two power sources on my APM. To avoid ground loops
Read more…Hi all! Am I correct doing this or should I not connect in parallel the batt for inputs and RX with the bat for outputs and fpv cam.
If I don't connect both batteries on parallel, I get only 5 mins of flight .When the battery supplying motor is at 20%
Read more…Hellow guys!!
Moved this question here. I have a delta wing with my APM 2.5 . Everything seems to be hooked up properly. Manually I control de surfaces ok. Even if a connect it to Mission Planner I can se the artificial horizon moving accordingly with
Read more…Hi!
I am setting up my wing with my APM 2.5. Everything is connected just fine. When I try manual mode, all surfaces moves as expected. However, when I turn on stabilize mode, something weird happen. When I do de pitch movement APM compensates as if I
Read more…Hi! I have an APM 2.5 and MinimOSD v1.1. The thing is, I have video and the data shown on the video. However, I don't know why the information shown on the video dissapears. If I press reset button, it appears again with correct data. The APM and the
Read more…Hi!I have a galaxy s2 with android 4.1.2. I also have the otg cable you suggest. I connect it to APM 2.5 with no battery supply and nothing happens. What is the proper way to connect it? I have different power supplies for apm and inputs and for outp
Read more…Hi all!
I do FPV using minimOSD to display data on screen. My question is if its possible to do both use minimOSD and a 3DR Radio to get telemetry on my laptop. However, I am only able to connect one of these two to my APM 2.5..aren't I??? Is there a
Read more…Hi all!
I use this digital servo http://www.goodluckbuy.com/md260-260-degrees-metal-digital-servo-for-fpv-pan-tilt-control-upgrade-md180.html to pan my camera. However I noticed that if I move it two fast, it reboots my APM 2.5. I searched and it seem
Read more…Hi all! Everything seems to work like a charm now in my bixler with 2.62 ardupilot firmware ( crossing fingers!! ). However, when I plotted the kmz on google earth I could see something was not right. It is clear to see how there is an offset on the
Read more…Hi guys!!
I don't know if it is the result or the consequence, but the think is I had a crash. I am checking APM 2.0 and I encountered some of the outputs pins a bit bended and the output pin nuumber one ( the one next to gps ) as well. I fix this, an
Hi!!
I have a bixler with APM 2.0. Recently I updated the firmware to 2.50 but now the behaviour is weird. When I turn stabilization on it goes really smooth, actually I think better than 2.40 . However, when I touch the stick the counter action is no
Read more…Hi everybody!
I need to calibrate the voltage sensor on APM 2.0 . To do so I need to be plugged through the USB but I need to connect the 5V Bec as well to inputs/outputs to see what voltage I get and then substract the 0.3 V it says on the menu.
Is it
Read more…Hi all!
I am using an APM 2.0 with ardupilot 2.40 and a frsky module. I am having trouble to get a 3D-fix. It takes a lot of time ( more than 2 min max explained in the wiki )and I need to reboot several times before it gets signal. I amb flying on an
Read more…Hi guys,
I've been trying to set up failsafe with my radio and apm 2.0. I want the RTH mode when I loss signal. I've been reading a lot but I don't find a step by step guide to do it. I know I have to set up the positions of the sticks on the radio ,
Read more…Hi everybody!
I have an AMP2.0 with a frsky module. When I turn stabilization mode I can't release the sticks and see the plane flying horizontally. If I do that, the plane dives and can't hold the altitude. Even if I fly without throttle ( with throt
Read more…Hi all!
I've followed the tutorial on several webs including the one which is really well explained here in diydrones to configure 6 mode flight on my RX. The thing is that the values present on that tutorial does not work for me so I keep moving up
Read more…Hi everybody,
When I test stabilization mode on my APM 2.0 it works just fine, the only thing is that the rudder does not react to yaw movements. Pitch and Roll acts to stabilize the plane but not the yaw.
I can move the rudder in Manual mode so appare
Read more…Hi everybody!
I've been trying a lot of things but none of them seems to explain what's going on.
I have a flysky 9x with er9x firmware. I have the 3 pos switch button programmed to work as a mode changer. In fact this are the flight modes I have set u
Read more…Hi everybody!
I am kind of new in the RC Airplane world. I amb looking into purchasing an APM kit. However, I am kind of lost because as I understand, ardupilot is an extension board for arduino board. However, when I see APM 2.0 seems to be all integ
Read more…