Gender
Male
About
Location
COIMBATORE,TAMIL NADU
About Me:
RECENTLY GRADUATED LOOKING FOR SOME ADVENTURE IN AVIONICS
Please tell us a bit about your UAV interest
AUTOPILOT SYSTEMS LURES MY INTEREST TOWARDS THE UAVS
Hometown:
COIMBATORE
Activity Feed
"Thanks Javier, Andre and Graham .
Ill try to reduce the vibrations."
Ill try to reduce the vibrations."
"Is it possible that i calibrated the accelerometer wrongly ?can that lead to some thing like this ?"
"I was planning to fly in loiter
I tried to take off
Then immediately the quad gained height and went out of control
I tried switching off the remote to trigger remote failsafe
Nothing seemed to work"
I tried to take off
Then immediately the quad gained height and went out of control
I tried switching off the remote to trigger remote failsafe
Nothing seemed to work"
"Thank you for the reply Javier.
You mean to say that the vibration was the cause for my drone to gain altitude and then crash ?
no issues with mag ?
cause it went as high as 1.25 km up in the sky"
You mean to say that the vibration was the cause for my drone to gain altitude and then crash ?
no issues with mag ?
cause it went as high as 1.25 km up in the sky"
I started flying my quad copter with a pix falcon.When i tried to takeoff, it suddenly started gaining height and went up 1 km and then fell down.Can anyone help me in identifying the cause for the crash ?I have attached the data flash log from the…
"Guys i flew my quad around 1.5km with the 500mw 915mhz telemetry. I have 99% signal strength even at 1.5km . But if i give any command to my quad at 1.5 km through telemetry, my quad is not responding. Any idea why it is happening like this. ? i try…"
"Thank you Very much for the reply Shyam.
I'll do the same. Shyam Balasubramanian said:
Glad you enjoyed it. Have you visited the website dev.ardupilot.com, for developers? I dont have a link to a step by step guide atm. What i would suggest is to…"
I'll do the same. Shyam Balasubramanian said:
Glad you enjoyed it. Have you visited the website dev.ardupilot.com, for developers? I dont have a link to a step by step guide atm. What i would suggest is to…"
"But how will i have the tx power of 500 mw if i set my tx power in Mission planner to 100 mw ?
Can i get long range by giving 5v Seperately in case Pixhawk or APM is not able to deliver required current ?"
Can i get long range by giving 5v Seperately in case Pixhawk or APM is not able to deliver required current ?"
"Guys i Have a Doubt. The telemetry is 500Mw . But in the SIK radio settings window in Mission Planner or APM Planner has the Maximum Power setting of 100 Mw i.e we set 20 as the transmission power settings. So how does that help us use this 500 Mw…"
"Hi Shyam , Nice post . Really good work. I'm learning Arducotper arduino code..If you can help me with the step by step code understanding of Arducopter code it would be great. If you have any links to your blog please share that too "
"Guys thank you for the reply.I got i working by tweaking Mission planner to get servo controls in the Servo tab. Extended the controls for Servos 12, 13 and 14. Thank you very much for the replies once again. "
"How to configure RC12/ RC13/ RC14 for servo or led control using mission plannner guys ?"
"Guys if i want to control servo or led on RC12/RC13/RC14 i.e. AUX pins 53/54/55 using mission planner what should i do. ?
Because the Mission planner "Servo" Tab has only control for RC5 - RC11.
please let me know if i can modify anything in the…"
Because the Mission planner "Servo" Tab has only control for RC5 - RC11.
please let me know if i can modify anything in the…"
"Even if i define aux pins 53/54/55 for servo control or led on off where will i have the control for them to control or switch on or switch off ?"
I'm trying to use the aux pins in the pixhwak to control servo or leds. I am able to use the RC9 / RC10 / RC 11 for the same. But i want to extend it to RC12 / RC13 / RC 14 .i.e. Aux out 53/54/55 in pixhawk. But there are no servo buttons in mission…
