Andre Crawford
  • Male
  • Cape Town
  • South Africa
Share Twitter
  • Blog Posts
  • Discussions (12)
  • Groups
  • Photos
  • Photo Albums
  • Videos

Andre Crawford's Friends

  • Cronselaar
  • Garth

Andre Crawford's Discussions

Ardupilot Config Tool v1.4.12 Problems Uploading

Started this discussion. Last reply by Andre Crawford Dec 28, 2009. 2 Replies

NEMode

Started Jun 24, 2009 0 Replies

Unmanned Vehicle

Started this discussion. Last reply by James Cohen Jun 8, 2009. 1 Reply

 

Andre Crawford's Page

Latest Activity

Johann Van Niekerk replied to Andre Crawford's discussion AVRSIP2. + Where to buy in South Africa
"HI Andre I can help"
Jun 13, 2011

3D Robotics
Chris Anderson replied to Andre Crawford's discussion Powering up ardupilot for the first time.
"It really depends on exactly when you ordered it--you can't tell from the stencil. I'd just load the current code (2.4.6) and check it out. If the mode toggle works, then you're fine. You won't need the AVR programmer."
Jan 2, 2010
Matt V replied to Andre Crawford's discussion Powering up ardupilot for the first time.
"Jordi, I know this thread is old so please forgive me... I have the old board too (11/something/2008 stenciled on the board.... I don't have it close by at the moment) and am now getting around to having a go at it. I am aware of the bad flash…"
Jan 2, 2010
Andre Crawford replied to Andre Crawford's discussion Ardupilot Config Tool v1.4.12 Problems Uploading
"Hi Chris Yes it does read properly, ok so it works then. thank you very much for getting back to me. Regards andre"
Dec 28, 2009

3D Robotics
Chris Anderson replied to Andre Crawford's discussion Ardupilot Config Tool v1.4.12 Problems Uploading
"When you read the code, does it show that it was in fact properly written? Sometimes that error message shows up even when nothing is actually wrong."
Dec 28, 2009
Andre Crawford posted a discussion

Ardupilot Config Tool v1.4.12 Problems Uploading

HiI'm having some problems loading a mission from the Config Tool application to the Ardupilot board. Evertime I try to load a basic mission it gives me a error "Something is wrong"Can anybody please help, I've managed to load code to the board before but now i'm having some problems and i'm not sure why.RegardsAndreSee More
Dec 28, 2009
Andre Crawford posted a discussion

NEMode

HiI fired up my AutoPilot, and i wanted to run the NEMode for testing, while looking at the code though I noticed that it has RTL activated (#define RTL 1) is this correct as when you want the autopilot to be in way point mode that needs to be specified as 0 correct?RegardsAndreSee More
Jun 24, 2009
James Cohen replied to Andre Crawford's discussion Unmanned Vehicle
"Hi Andre, As far as I understand the Ardupilot v1 code should adapt well to this. James"
Jun 8, 2009

Comment Wall (4 comments)

At 10:23am on February 5, 2009, Garth said…
Got connected hopefull get a call for the avr kit later
At 11:06am on February 14, 2009, Garth said…
Glad to see you are working hard
At 9:26am on February 16, 2009, Gagarien said…
Hi Andre I found this company: Sivan Electronic Supplies elecsupp@global.co.za esupplies@global.co.za Tel +27 (0)11 887 7879

Have not tried them yet! theyare in Sandton.
At 10:41am on March 29, 2009, Cronselaar said…
Hi, did you get the autopilot to work? I still need to order the boards ect. I would like to know if it is worth the effort and if customs have anyprobs with the autopilots? I would really like to get a AP off the ground. Anyhow, I'm studing BEng Mech at UP. So i might have a bit of programming help :)

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Social Networking

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service