Tommy
  • Male
  • China, mainland
Share Twitter

Tommy's Friends

  • Anish
  • Mark Willis
  • Paul Mather

Tommy's Groups

Tommy's Discussions

Upload/Dowload to ArduPilot

Started this discussion. Last reply by dylan Dec 10, 2011. 7 Replies

I use Arduino to upload program to ArduPilot.  Could soemone advise me how to download the program from ArduPilot?  I want to know the existing setting of my  ArduPilot for PID adjustment .  Thanks.Continue

Tuning PID values of Clouds Fly

Started this discussion. Last reply by Tommy Nov 22, 2010. 3 Replies

Hi, I tested my ArduPilot today.   My Clouds Fly is controlled by Elevator and Aileron with no Rudder. Stablize,  FLY by Wire and RTL modes were all in good order.  Then I uploaded a simple route for…Continue

Tags: Tunning

ArduPilot GCS cannot display Course from 180 to 360 degree

Started this discussion. Last reply by Darren Ng Oct 7, 2010. 11 Replies

Hi, recently I did ground test by holding my ArduPilot, ArduIMU+, MTK GPS(NMEA setting) and XBee in hand and walking around.  I found that everything displayed well on ArduPilot GCS, except when I…Continue

Viewing ArduPilotGCS - Beta2 by Netbook of 1024 x 600 resolution

Started this discussion. Last reply by Paul Mather Oct 24, 2011. 8 Replies

Hi, I have a netbook of resolution 1024x600 with Windows 7.  Comparing with my desktop, I cannot scroll down the window of GCS to view the battery level and throttle value.  Would somone advise me…Continue

 

Tommy's Page

Latest Activity

Tommy posted photos
Thumbnail
Thumbnail
May 1
dylan replied to Tommy's discussion Upload/Dowload to ArduPilot
"ok, I have the xsc xbee's because all others are out of stock. Trying to get them to work above 9600 but cant. If you know of a way please point it out. :)"
Dec 10, 2011

DeveloperMichael Oborne replied to Tommy's discussion Upload/Dowload to ArduPilot
"9600 buad on telemetry is to slow."
Dec 10, 2011
Martin Szymanski replied to Tommy's discussion Upload/Dowload to ArduPilot
"If you uploaded new and did not save the previous variables then likely the pid adjustments are lost.  "
Dec 10, 2011
dylan replied to Tommy's discussion Upload/Dowload to ArduPilot
"ok I got it to connect but after about 1 min I get this error "B|::?'dB:6j2}lost 11 pkts 231bps 923 loss 11 left 7 mem 38519992Mavlink Bad Packet (crc fail) len 40 crc 63739 pkno 30:"[p%lost 59 pkts 234bps 922 loss 12 left 1 mem…"
Dec 10, 2011
dylan replied to Tommy's discussion Upload/Dowload to ArduPilot
"I Want to change baud line #define SERIAL3_BAUD        9600 Once the APM_confih.h file is edited how do I get it loaded??? Is there a guide I'm missing?"
Dec 10, 2011
Tommy replied to Tommy's discussion Upload/Dowload to ArduPilot
"Thanks Graham!  "
Nov 20, 2011

ModeratorGraham Dyer replied to Tommy's discussion Upload/Dowload to ArduPilot
"As far as I know you can't download from Ardupilot, only write the new to it."
Nov 19, 2011
Tommy posted a discussion

Upload/Dowload to ArduPilot

I use Arduino to upload program to ArduPilot.  Could soemone advise me how to download the program from ArduPilot?  I want to know the existing setting of my  ArduPilot for PID adjustment .  Thanks.See More
Nov 10, 2011
7 Comments
Tommy commented on Peter Bell's blog post German Multicopter Lifts Human Pilot
"Awesome!  We can fly to school and office later! "
Nov 7, 2011
Tommy commented on James masterman's blog post Mapping with Ardupilot
"Very good job!"
Nov 7, 2011
Paul Mather replied to Tommy's discussion Viewing ArduPilotGCS - Beta2 by Netbook of 1024 x 600 resolution
"Thanks. There may be some recent changes to the MAVlink protocol that I might not be compatible with. I don't know when it's happening, so I can't say when I'll have to update my code."
Oct 24, 2011
Tommy replied to Tommy's discussion Viewing ArduPilotGCS - Beta2 by Netbook of 1024 x 600 resolution
"Hi Paul,   I have stop my Ardupilot project for a while and recently I start connecting my stuff.  I find that your GCS is much better than the one provided here.  I will do a flight test soon and many thanks for your contribution."
Oct 24, 2011
Tommy posted a status
"Making gyro-camera mount"
Oct 7, 2011
0 Comments
Tommy replied to Mark Willis's discussion Making Digital Elevations Models (DEM) on the cheap
"Many thanks for your detail explanation.  I will follow the instructions and buy you a cold beer later:)"
Feb 23, 2011
Paul Mather replied to Tommy's discussion Viewing ArduPilotGCS - Beta2 by Netbook of 1024 x 600 resolution
"I didn't mean to try to steal you as a "customer" (we're both free anyhow)... but I've specifically designed mine to work on small resolution screens...as my plan is to use it on a 1024X600 netbook myself."
Jan 5, 2011

Profile Information

About Me:
From the blue blue sky
Tell us a bit about your UAV interest
for mountain rescue
Hometown:
HK

Tommy's Photos

Loading…
  • Add Photos
  • View All

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Social Networking

Top Content 

1 Mapping Mission Ride Along

Mapping Mission Ride Along
2 APM 2.5 from hobbyking

APM 2.5 from hobbyking
3 Alt_hold and loiter acting crazy

Alt_hold and loiter acting crazy
4 Looking for best laptop screen to see in the sun

Looking for best laptop screen to see in the sun
5 New micro-cameras emulate insects' compound eyes

New micro-cameras emulate insects' compound eyes
6 ArduPlane 2.73 released

ArduPlane 2.73 released
7 APM Copter 2.9.1.b has been released

APM Copter 2.9.1.b has been released
8 3 axis Camera Gimble connections.

3 axis Camera Gimble connections.
9 Thirty Days (#17): 12-rotor close up

Thirty Days (#17): 12-rotor close up
10 Mechanical Hands From A MakerBot: The Magic Of Robohand (From Makerbot blog news)

Mechanical Hands From A MakerBot: The Magic Of Robohand (From Makerbot blog news)

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here. 

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service