Michael Dornisch
  • Male
  • Philadelphia, PA
  • United States
Share
  • Blog Posts
  • Discussions (3)
  • Groups
  • Photos
  • Photo Albums
  • Videos

Michael Dornisch's Discussions

Battery Monitor Works on Pixhawk 1 but not Pixhawk 2 Cube

Started this discussion. Last reply by Andre K. on Thursday. 7 Replies

I'm currently having issues with getting the battery monitor to work properly on my Pixhawk 2 Cube from ProfiCNC. I thought that perhaps I had the wrong pins selected, but the Pixhawk 2 manual states…Continue

Tags: pixhawk2, attopilot, monitor, battery

 

Michael Dornisch's Page

Latest Activity

Andre K. replied to Michael Dornisch's discussion Battery Monitor Works on Pixhawk 1 but not Pixhawk 2 Cube
"In that case, use Qgroundcontrol or APMPlanner2. It's an incredible achievement to cock that up if mission planner in fact messed it up. That would require some crazy logic to do so, as the data is sent over accordingly to mavlink…"
Thursday
Ultrafuge replied to Michael Dornisch's discussion Battery Monitor Works on Pixhawk 1 but not Pixhawk 2 Cube
"IIRC you need MP 1.3.48.3 (beta) or higher."
Thursday

MR60
Hugues replied to Michael Dornisch's discussion Battery Monitor Works on Pixhawk 1 but not Pixhawk 2 Cube
"Maybe it is a similar issue I found where in fact, after any change in mission planner in that current monitor window, you actually need to reboot the pixhawk board and reconnect mission planner to see the changes. Have you tried that ?"
Jul 18
Michael Dornisch replied to Michael Dornisch's discussion Battery Monitor Works on Pixhawk 1 but not Pixhawk 2 Cube
"Thanks, I was sure to account for that. I was able to verify that the Attopilot was connected correctly. I verified with a multimeter. Unfortunately, the problem still persists."
Jul 17
Andre K. replied to Michael Dornisch's discussion Battery Monitor Works on Pixhawk 1 but not Pixhawk 2 Cube
"My bad. I did not mean _curr_pin Also check that current and voltage pins on power module connectors are swapped correctly, Pixhawk2 has pin 3 and 4 swapped on the power module clickmate connectors."
Jul 14
Michael Dornisch replied to Michael Dornisch's discussion Battery Monitor Works on Pixhawk 1 but not Pixhawk 2 Cube
"Could you elaborate on this? The BATT_CURRENT_SENS is set to 3, as stated in the manual. Would an incorrect current sense pin also cause me to not read any voltages with the on the voltage sense pin(2)?"
Jul 14
Andre K. replied to Michael Dornisch's discussion Battery Monitor Works on Pixhawk 1 but not Pixhawk 2 Cube
"Set BATT_CURR_PIN correctly :)"
Jul 14
Michael Dornisch posted a discussion

Battery Monitor Works on Pixhawk 1 but not Pixhawk 2 Cube

I'm currently having issues with getting the battery monitor to work properly on my Pixhawk 2 Cube from ProfiCNC. I thought that perhaps I had the wrong pins selected, but the Pixhawk 2 manual states they are PA2 for voltage and PA3 for current. My test has been to take 3 battery monitors, and wire both a Pixhawk 1 and pixhawk 2 plug to it. I would plug into the pixhawk 1 first, to confirm it works correctly, and then into the pix2, where I couldn't get it to read voltage. I have tried this…See More
Jul 14

Profile Information

Please tell us a bit about your UAV interest
I want to build smarter autonomous UAVs.
Hometown:
Philadelphia

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

Season Two of the Trust Time Trial (T3) Contest 
A list of all T3 contests is here. The current round, the Vertical Horizontal one, is here

© 2017   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service