"I've updatet to the latest FW (Hexa / 08.05.). After some tries, I could connect to terminal. I goes to setup and enter motors. But there are no motors spins. I also pushed the ARM-Button and retried this (3 short and the other one with…"
Anselm's Discussions
PX4 hey/octo with gimbal?
Started Mar 19 0 Replies 0 Likes
Hey!Does anybody know: Can you create an hex or octosetup (with IO extension-board) and can you connect a gimbal to IO or FMU board also? Or must we create a seperate gimbal-controller?Best regards…Continue
Tags: octocopter, hexacopter, px4, gimbal
build next copter with PX4 - anybody knows to use current sensor?
Started Mar 15 0 Replies 0 Likes
Hey!I want to build my next hexa-copter with px4 fmu/io/flow/lea6h. The electroics arrived me a few days ago. Now I'm construction the power-pcb who I will esc connect. Know anybody: Can I use the…Continue
APM 2.0 onboard GPS change to uBlox LEA 6 - possible?
Started this discussion. Last reply by Anselm Feb 22. 3 Replies 0 Likes
Hi!I've a APM 2.0 with the soldered onboard Mediatek GPS and magnetometer. Now I want to buy a uBlox LEA 6 GPS module. Can i use it parallel to the onboard GPS? Or is it not possible?If I can use it,…Continue
Can I use two 3DR radio kits parallel?
Started this discussion. Last reply by Anselm Aug 22, 2012. 4 Replies 0 Likes
Hi! I'm using one 3DR 433 MHz Kit for my Arducopter (telemetry). Now I want to create an second control-system for cameras. Can i use a second 3DR radio kit on 433 MHz (900 is not allowed in germany)…Continue
Anselm's Page
Latest Activity
Anselm replied to John Mulligan's discussion Px4 Testing"I think I've a little problem: I've build described hexa-copter. Yesterday I screwed the props and connected the lipos. I armed the copter and took a really little bit throttle and hold the copter by hand from top. But the motors took so…"
Anselm replied to John Mulligan's discussion Px4 Testing"Great! That's it. The copter seems so be ready, now. The data (flighdata>tuning) shows a really stable line. Further I must check which LiPos (3 or 4s) I can/must use and then goes to the thirst flights - next week. Best regards!"
Anselm replied to John Mulligan's discussion Px4 Testing"Hey!
Actual 2.9.1b Hex-Firmware is uploaded, minimOSD, 3DR radio telemetry are installed, declination and radio-controller is configured. All motors runs on, but I've a little problem:
If I connected it to MP or QGround, the sensors send a…"
Anselm replied to John Mulligan's discussion Px4 Testing"This means my first problem: I've used another pc and there was no problem. Back on my pc I try it again. But I didn't get the semaphore message - he waits at correct com port and then runs to other ports. I reinstall driver and and and...…"
Anselm replied to John Mulligan's discussion Px4 Testing"Now, I found a bug?! I've connected the ESCs to servo 1-6 (like this https://code.google.com/p/arducopter/wiki/PX4FMU_IORC?wl=en for hex-x). If I Arm the copter and take throttle the motors 1-4 runs and the motors 5 and 6 stands still.…"
Anselm replied to John Mulligan's discussion Px4 Testing"Hey!
I've some questions to the new PX4. I install the windows-usb driver and then the latest FW PX4FMU und PX4IO. After some issues with my pc I could connect. I don't know where the problem was. On our noteebook it was no problem (both…"
Anselm posted a discussionPX4 hey/octo with gimbal?
Hey!Does anybody know: Can you create an hex or octosetup (with IO extension-board) and can you connect a gimbal to IO or FMU board also? Or must we create a seperate gimbal-controller?Best regards from Germany.See More
Anselm posted a discussionbuild next copter with PX4 - anybody knows to use current sensor?
Hey!I want to build my next hexa-copter with px4 fmu/io/flow/lea6h. The electroics arrived me a few days ago. Now I'm construction the power-pcb who I will esc connect. Know anybody: Can I use the AttoPilot current sensor (SEN-09028 range 90A/50V at 3.3V)? Then I could solder it directly to my power-pcb (board) before I screw it in/on frame...Best regards from Germany. :-)See More
Anselm replied to Anselm's discussion APM 2.0 onboard GPS change to uBlox LEA 6 - possible?"Thanks very much. I still wait for my new ublox gps. :-)"
Parke @ ParkeFlyer replied to Anselm's discussion APM 2.0 onboard GPS change to uBlox LEA 6 - possible?"I haven't done this, but maybe this will help...
http://code.google.com/p/arducopter/wiki/GPSDisable"
Scott Berfield replied to Anselm's discussion APM 2.0 onboard GPS change to uBlox LEA 6 - possible?"You need to disable the on board GPS. Then you can plug the uBlox into the GPS port on the APM 2.0. I don't think you can have both active at the same time. If you look around, you'll find info on how to disable the on board unit. I think…"
Anselm posted a discussionAPM 2.0 onboard GPS change to uBlox LEA 6 - possible?
Hi!I've a APM 2.0 with the soldered onboard Mediatek GPS and magnetometer. Now I want to buy a uBlox LEA 6 GPS module. Can i use it parallel to the onboard GPS? Or is it not possible?If I can use it, which cable I must use (uBlox to APM) and where I must change the settings for GPS - that the data from external uBlox GPS will be used and not the onboard-data? I'm using missionplanner with arducopter.Best regards from germanySee More
antoine replied to Anselm's discussion GCS CopterLink via 3DR"Ok thanks, so no way to simply use the USB module?
Antoine"
Anselm replied to Anselm's discussion GCS CopterLink via 3DR"Hi! You ned a second Air-Module and there you must connect the RX/TX wires to the BT-TR/RX. The actual gcs-copter version is for my pad/phone not usable. I still wait for an update from the developer. In the bug-tracker (~ #26 or 27) is a link to an…"
antoine replied to Anselm's discussion GCS CopterLink via 3DR"Hey Anselm and all,
I am very interested in how to set that up.
How do you do the wiring?
I have a 3DR ground module that is USB and I am unsure how to use it with BT.
ANTOINE"
Profile Information
- About Me:
- I'm just flying since a few years. Now i will change btw. expand my helis with multicopters.
- Tell us a bit about your UAV interest
- I'm interested in octocopters with FPV and will take some landscape videos (GoPro hd2).
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
ArduCopter User Group
1283 members
-
Moderators
24 members
-
ArduCopter (traditional …
180 members
-
Queensland
4 members
-
Turkish Ardu Group
5 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
