dincer hepguler
Share

Dincer hepguler's Friends

  • M.Erdi Erdogdu
  • Enes ÇALDIR
  • iTech
  • Ersin Acar
  • Melih Karakelle
  • Jean-Louis Naudin
  • Raytrace Nomad
  • Reto
  • Andrea Salvatore
  • Jordi Muñoz
  • Chris Anderson

dincer hepguler's Groups

dincer hepguler's Discussions

dont see any hardware tabs in my mission planner

Started this discussion. Last reply by dincer hepguler May 26, 2013. 2 Replies

 

dincer hepguler's Page

Profile Information

About Me:
robotics hobbyist and enthusiast. 3D Graphics and design. Nature lover, bonsai maker...
Please tell us a bit about your UAV interest
borsaci06.com
Hometown:
ankara - turkey

dincer hepguler's Videos

  • Add Videos
  • View All

Dincer hepguler's Blog

incredibly cheap OSD from Hobbyking...

Posted on July 16, 2011 at 7:30am 3 Comments

friends,

has anyone seen this?... http://www.hobbyking.com/hobbyking/store/__17141__HobbyKing_G_OSD_On_Screen_Display_with_GPS.html

 

a very small osd at $36 with the gps module included... it…

Continue

Solar Falcon first attempt with ArduPilot and Nunchuck Acc

Posted on May 1, 2009 at 5:30am 15 Comments

my first ground test with APv1 was full of problems. till last summer i am working on my hand made airframe. finished the plane and solar wing is connected and tested. system works well, i tested it for 55mins until my radio battery drained.

system: 35 mhz 6 ch radio (because im planning to use 900mhz x-bees for telemetry and 2.4ghz video downlink), solar wing with ailerons, planned to use APv1 on throttle and rudder. stabilization on ailerons… Continue

Comment Wall (4 comments)

At 3:19pm on April 28, 2009, Ugur Bozkurt said…
merhaba,
uav ile ilgili bir tez hazirliyorum. fakat sensor kalibrasyonu icin osiloskopta bazi olcumler yapmamiz gerekiyor. co pilot sensorunun ne kadar dondugune bagli olarak bir cikis gozlemlememiz gerekiyor. servonun nasil tepki verdigi yani.
kullandigimiz aletler cpd4(fma co pilot), sub micro servos, lipo batterry, dx6i radio controller.

gerek baglanti gerek osiloskoptan aldigimiz bilgi olsun ne yapmamiz gerektigi hakkinda pek fazla bilgimiz yok.
bu konuda yardiminiza ihtiyacimiz var..
tesekkurler.
At 2:51am on May 2, 2009, Reto said…
Hi Dincer. I feel I am only a good DIYer when things are running like I'd like to. But I spend more time on things that aren't!! It's the learning process I like, I think. Good luck with your progress
At 5:12am on May 2, 2009, Reto said…
Same goal to auto-land with EZ1 sensor but code space is getting scarce, even with 2 boards. Maybe with one AP 328 (I got already but didn't prepare it yet) and one AP 168 it will be ok. Or I'll add a spare Arduino Pro Mini, it weights almost nothing.
At 5:39am on May 2, 2009, Reto said…
I am not so advanced with autolanding. It's just in my head. You should start a permanent blog in which you could describe it, show your problems and progress. Would be nice to follow.

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

© 2017   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service