Do you have any experience with these lipo batteries? I run a 7.2 NiMH battery, is it possible to run these 2s lipo and more (Ovonic Rebel)? I've read that certain battery combinations can heat up the motor and ESC, but don't know which one is the be
Read more…Hello, I have a project which requires a gas tank sensor to talk to the APM 2.8 The gas tank sensor is the typical 0-190Ω variety like this:
Read more…I am building a quadcopter from some parts that were donated to me and I am unsure of how exactly to connect the power distribution board, esbs and flight controller. This is my second build and a lot more complex than my first. I was hoping I could
Read more…Does anybody know if you no longer need a teensy board? I still have an older version of 'plane' on my pixhawk. I had to get a new Taranis plus my old one broke. Just trying to set up the telenetry again. The new / used X9D radio had newer FW on it s
Read more…Hope this helps.
Futaba 2008SB Receiver. T16s7 Trainsmitter.
Pixhawk 2.4.8 two different units,
When the arming switched is pressed on the platform,
The throttle channel 3 +5 VDC goes to zero.
Reprogrammed the setup for channel 8 to be the throttle,
Sam
Read more…Hi Guys,
Could you give me some impressions about the GCS you use? If you can answer these questions for me, it will be very helpful:
- What is your drones’ usage?
- Which GCS do you use and why?
- What are the main features you use?
- What are the best a
Read more…Some types of aerostructures are not RF transparent at 2.4GHz, and some aircraft designs use internal RF shielding. Both types require externally mounted RC antennas. We are fabricating an aircraft using carbon fiber aerostructures that are not RF tr
Read more…Hey! Friends, I found several charts about brushless motors (Brushless Motor Chart), which explain the relationship between motor size, voltage, and speed very well. Honestly, this knowledge is very helpful for beginners. Saving these charts will sav
Read more…Hello!
Im going to some university work to show, some automation thing for my class. And I will talk about UAV. I have some question, Can I talk about fly by wire system? The fly by wire system airplane is the similar in the UAV? And somebody have a g
I am building my first 5" camera drone. I need suggestions on a suitable Flight Control Stack and quad ESC with at least 45 amps. I don't want a bare bones controller but one that has lots of room to grow with new features. I will be using BetaFlight
Read more…I have been able to calibrate the vertical lift esc (4-in-1) but can't figure out how to calibrate the pusher ESC...
Read more…up to 50% discount
10% off over $69 everything
link:https://www.ampow.com/pages/ovonic-summer-sale
Road to Drone Autonomy Series is a 3-part series where we feature Drone Solution Providers (DSPs) from three different geographies from the European subcontinent to highlight the experiences and journey to adopting autonomous drone operations f
Read more…Hello everyone,
I've searched a lot about developing skills as a drone pilot. In my searches, Taking training to become a drone pilot from a particular academy is expensive.
Can you guys suggest to me, What are other ways to be skilled as a drone pil
Read more…Please I need your help... I am in need of a company/ outlet to purchase... high volt . large capacity, Hi C rated Lithium battery packs. If you have any info please let me know. 96 volt... 24S around there ... but any info to get me started i
Read more…Hello,
We have a quadcopter we've built using Emlid's Edge flight controller. Everything is well calibrated (according to QGroundControl) and looks fine. Whenever we attempt to takeoff, the drone flips over on its side pretty much instantly. It is a f
Read more…I'm looking for the cheapest possible 5 kg and 6 kg thrust brush and brushless motors to build throwaway dirt-cheap quad- and octocopter drones.
Read more…I am looking for a reliable supplier of commercial grade Lithiul battery packs for an high lift UAV... 48 volt to 96 volt... any info would be very helpful Thank you
Read more…HI.
I am trying to find a supplier of good quality lithium battery packs. 48v to 96 volt... I am looking to work with them to produce several packs correct for my application,
Any info will be greatly appreciated.
Thank you...
Read more…