Hello Everyone,
I currently have a client who hired me to do an aerial survey/ Aerial Mapping of a portion of land where they plan to build homes. They asked me about the accuracy of my outputs and if I use a land points on the ground to get accurate
Read more…Dear Everybody.. I am Dom. New to forums & drones. I am, sadly, not a micro electronics person. Recently I got a Parrot Mambo. I hugely want to make a tiny wifi fpv camera setup for it. I think from your sites pictures that I am in the right place. S
Read more…Hi, this is my first post.
I'm part of a small environmental consultancy looking to expand our current ground survey (RTK GPS) capability with drone based topographic/environmental mapping.
The main application is for accurate (better than +/- 50mm) t
Read more…Hello everybody.
I am currently using the APM v2.8 as a flight controller for my quadcopter. I am trying to get it to perform autonomously (in auto mode with a set flight plan from mission planner) as soon as the battery is connected, or to get it to
Read more…It seems that Master Airscrew have too much props :)
I'm very satisfied with the MR series and surprised now that they have a FREE giveaway on10x4.5" Multi Rotor props.
The free props you can find here: https://www.masterairscrew.com/collections/mr-ser
Read more…We are the group of enthusiasts who find technology as the ladder to future– for this reason we have created an application with which the world can become a better place.
Our project called Dron-x stipulates 7 stages of the drones’ application than
Read more…Hi DIY Drones
I’m currently working on a project trying to create an autonomous flying wing (https://hobbyking.com/en_us/hobbykingtm-skyray-flying-wing-fpv-model-1213mm-epo-pnp.html).
I currently have an Erle-Brain 3 flashed with the APM autopilot. I h
Read more…Hello,
I am trying to arm my pixhawk and I keep failing the check for the 3D fix. However, I do not have a GPS module plugged into the pixhawk and I am just trying to use RC control. My question is, how do I edit Prearm checklist to remove the GPS f
Read more…Greetings,
I'm currently sampling data from a Hobbyking digital pitot tube. The sensor on this device is a MS4525 differential pressure sensor.
I've noticed that in a static environment the minimum change between the readings seems to be 5 counts. For
Read more…Hi!
I'm new in this world so i have a lot of questions, today i hope you guys can answer me just one. The components of my drone (FC, reciever, A/V trans, gps,etc) can generate interference between them? I was wondering how to place all of them on my
Read more…I think I'm almost done with my drone, but I have run into a problem.
So the Pixhawk doesn't supply power to the servo rail, but that is the only thing my receiver is connected to... I'm trying to research how to power the receiver without a separate
Read more…I had an old APM flight controller (3.2.1 fw) that I thought I would put to work on a HEX. When I tried to calibrate the compass using MP 1.3.44, I got a "Compass Calibration FAILED" message. No matter how I tried, I couldn't get the compass to cal
Read more…I have been practicing Auto-mission using Pixhawk, Arducopter firmware and mission planner from quite some time. In the last flight, however, in an attempt to check the failsafe, it was observed that the quad started gaining altitude even after enter
Read more…YourVuz is a monthly drone video contest. The contest is built around monthly themes often tied to holidays. The winner gets a $500 cash prize. Here is a link to the announcement of this month's theme. Submissions due by February 22nd:
Read more…Instead of connecting a receiver to my quad copter's can I do something so that I am able to send commands to the flight controller using my android smartphone and WiFi?
Read more…HiI am putting an S1000 together with Pixhawk. On my Hex I'm using 200A Mauch but I'm unsure about the current draw on the S1000+ with 20,000 mah battery and possibly 2 20,000 mah batteries. If I go with 2 batteries I should probably have one power m
Read more…Hi,
I'm searching good umbrella arm joint for 25mm tube (hexacopter, 6-7kg, 15-17' propellers). Maybe You know good one? I found on markets some stuff, but I don't know which choose...
Hi all devs.
We are currently a team of researchers at Aalborg University looking into indoor navigation using SLAM on the recently launched Intel Aero Ready to Fly drone equipped with an STM32 running DroneCode (PX4 stack) and an Intel Atom processor
Read more…
Read more…
