Early, I worked with APM2.6 with Raspberry Pi B+, Raspberry Pi A+ and all works fine.
Now I try to connect APM2.6 to Raspberry Pi 3 and Raspberry Pi Zero and I obtaned the next problem:
1) I tryed to connect with usb port and command
Read more…sudo mavproxy.py --
I've setup my survey plane with a canon s110 using CHDK, is there an upgraded Canon camera with better resolution that I can continue using CHDK with mission planner? Is there a better camera with the same size and better resolution?
Read more…sent command from MP to guided mode to a specific point and descent to 5M, well it went to the guided point but it kep descending well below 5M until it hit a low fence...I have looked at the logs and you can tell the desired ALT and actual ALT dont
Read more…Good day everyone,
I have a 3DR kit and I put together a quadcopter more than a year ago but last time I flew it I was having issues with it, the quadcopter was flying fine but when switching to LAND or RTL modes, it was acting all crazy and finally c
Read more…1. a soft cleaning brush
This is for some corners and gaps, and you can also use the pipeline pigging.
2. canning compressed air
This can clean the dirt of some "sensitive parts" such as the electric motor or circuit board around, which would not damage
Hi All,
While on a mission with our fixed wing UAV in a tropical country, flying a routine surveillance mission, the UAV started to roll with high amplitude movements, climb 10 m above its 150 m mission altitude, and fall.
We cannot figure out what cau
Read more…Hey guys I need a bit of help here. I am getting really frustrated. I can get the quad to lift off the ground. It requires constant input on my part to keep it from hitting something really hard. It will roll all of the sudden at almost a 45 degree a
Read more…Good day everyone,
I have an old 3D Robotics Pixhawk with Compass/GPS Module, Power Board and a Quadcopter Kit that I put together a while back.
I was thinking it is time to upgrade but I was wondering what is the best option nowadays, I see some new o
Read more…Mission planner closes every time with;
Map Tools > Prefetch and Prefetch WP commands
I am based in Zambia. Using Action Drone AD2 Ag with Slantrange 2P Multispectral sensor for NDVI images.
PixHawk Flight controller, Mission Planner build 1.3.41 on Wi
The Pixhawk mini doesn't have an Aux port. Has anyone had any luck getting a camera trigger configured on an airplane.
Read more…Hi, there i'm building a quadcopter on arduino (i use mpu 9250 ms5611). and i want to migrate the code of arduipilote "altitude hold" to arduino.
I read all the documentation in this link "http://ardupilot.org/dev/docs/". and also i downloaded all the
Read more…I bought a chinese clone radio and it had a different usb chip that wouldnt work with my smartphone drivers. So i am trying to find a genuine 3dr usb telemetry module or one with a genuine Ftdi chip. It might be difficult with 3dr not selling them an
Read more…First I want to say that I hope I put this in the right category. Second this is not something I am going to do right away. Its probably going to be 6 months before I put this into action. Just planning now so I can get a good design down and get eve
Read more…Does anyone have used a arduino mega configured to SD data logger? I've a Ardupilot V2.8. But I connect a FTDI on TX onto Telem port. I just get a character no readible. I need a little help.
Read more…Hello!
I have a script to extract GPS data from a text file and send MAVlink messages via the serial port. Currently I don't have the hardware and would like to test the functionality through simulation. Could someone tell me which virtual serial port
Read more…A little background.
This flyaway occurred on a dji s900 setup with a Pixhawk fc, dji hardware, and an ImmersionRX Ezuhf diversity receiver. I've flown this setup countless times in loiter, auto, and stabilized flight modes without problem. My transm
Read more…can I use DYS D2830 1300kv brushless motor (which is designed for airplane) in my quadcopter and what props should i used to get 1000gm of thrust..??
Read more…Good day mentors and friends,
I would like to build a drone with the following specs. Your suggestion and recommendations base on your expertise and experience will greatly appreciated.
hi,
i'm working on a project which aims to bridge the gap between simulink high level code
and arducopter low level code.
i bridge the gap by expanding the simulink library with block set(kind of toolbox) which represent arducoper components, such as m
Read more…Happened to experienced VR last week, I really enjoyed that and want to buy one now.
I have searched Amazon, GB and healthcabin for many days, but did not decide yet. My budget is around $300, it should be enough for simple VR.
anyone can give me some
Read more…