manual set roll and pitch
hey guys! Tell me please which MAVLink packets should i use for manual control UAV's roll and pitch directly?
Read more…
1 Reply
All Discussions (17281)
Sort by
Quaternium Spidex V3 Mapping Quad with Case and Extras
I built this with intentions to get into mapping. I set it up and played with it a few times but it sits around more than anything. Comes with everything pictured except for the receiver(free if you want it). Add your transmitter/configure it and
Read more…Problem mit der Failsafeeinstellung im Mission Planner mit einer Futaba T10j
Hallo Leute, nachdem ich nun einige Zeit mit meinem Reptile Copter in der Luft verbracht habe, wollte ich mal ein neues Gerät ins Auge fassen. Ich habe deshalb auf der Hülle meines Cheerso CX20 eine neue Installation mit APM 2.8, GPS, FPV Sender, und
Read more…NAZE32 rev6 + lemon rx + TARANIS = HELP ME!!!
so i got a 4in1 module from banggood and got it installed and working with my tiny whoop and proto-x. but im trying to get my diatone 150 with a lemon rx sat to bind, ive tried the "set spektrum_sat_bind=" in cleanflight with several different code c
Read more…Problem with AltHold / PosHold - dropping altitude!?
Hey,
i have a strange problem with my copter: it flies just great in stabilize mode and it stays on point pretty ok when using poshold. Now the strange thing: whenever i have it in poshold or alt hold and move the copter in any direction it will drop
Connecting and controlling high-end gimbals through PPM/SBUS/CANbus via pixhawk
I have been searching high and low (I believe) for information on how to connect an control high end gimbals for DSLR cameras that only support PPM/SBUS/Canbus etc. for example: https://www.gremsy.com/gremsy-h7
I need to be able to control the gimbal
Read more…Running SITL for PX4 with qGround Control
I am trying to run PX4 code through SITL simulation without any actual hardware. I am not able to use GeoFence and Follow me functions in the qGroundControl. Are these functions unavailable while simulating? I am not sure if I am doing something wron
Read more…Where can I find CMD ALT in Tlogs?
I am having issue with my dataflash logs that the CMD alt is not matching the actual altitude. I was hopping my Tlogs recorded this but when I am graphing it using mission planner I don't see any CMD Altitude.
Read more…Navio2 vs ardupilot mega vs revolution
Whats up guys. So when i first got into quads i did very little research on flight controller and ended up picking the revolution fc. I have three of them now. One on my 550 quad and one on my 250 size quad. So far the have been performong fine altho
Read more…Autopilot Designing
Hello, I have got a project of designing an autopilot for an amphibian UAV with waypoint navigation facility. I have difficulty in working on C programming. So, I feel it is better to work in MATLAB programming. But, I do not know how to do programm
Read more…2nd Annual Flying Robot international Film Festival - 11/17 in San Francisco
Hello DIY Drone Community!
For UAV enthusiasts in the San Francisco Bay Area, you might be interested in a couple of events coming up next week.
The Flying Robot international Film Festival returns to San Francisco’s Roxie Theater on November 17 at 7pm
Read more…Pixhawk Y6 Fell from the sky!
Hello,
I am fairly new to the copter screen. About a year. I have never posted on a forum before.
First build F450 Flamewheel with Naza-m Lite.
Second build Rctimer Y6 with pixhawk.
This post is about the Y6.
After about a couple dozen flights in whic
Read more…APM 2.8 dead?
My APM 2.8 flight controller stopped responding.
I dont remember should the PC make a sound when i connect the APM to the PC, but there is no sound.
There is just one orange stable light and thats it, no blue, no red.
Not reponding on batter and USB c
How can I utilize external IOs in Pixhawk.
I flew quite a lot with pixhawk system with various setups and know about connecting devices like sonar, optical sensor or lidar.
I felt confident configuring pixhawk system until recently I have an order to setup a pixhawk drone for autonomous sprayi
Read more…Selling Skywalker X8 black new and other accessories
Hi,
I'm selling this RC items because I will focus in multirotors.
1x Skywalker X8 Black (NEW) - 140.00 EUR
1x Scorpion SII-3020-1110KV (V2) + Replaceable kit (shaft and bearings) - 85.00 EUR
2x AERONAUT CAM-CARBON 12x6.5 - 8,00€
1x ALU PRECISION SPINNE
PPM
Hi all,
I am using a futaba transmistter and receiver (8 channel). Does anyone know what does each channel do?
Do the channels control pitch,roll,throttle etc.?
Read more…yaw with no stick input
On my second test flight I noticed that the copter was slowly turning without me applying any rudder input. During the first flight this was not the case.
Also, when I switched to circle mode, the front of the copter did not point to the centre of the
Read more…TeraRanger and Arduino
Hi guys!
Does anybody have an idea of how to use TeraRanger with the arduino? I am currently trying to read the values from the arduino but do not know how to. Anybody has a written code that can read what the TeraRanger is reading? I am using a TeraR
Read more…FLIR Vue Pro / Tau & GoPro Gimbal
Hi DIY Drones, we'd like to let you all know about the new Helium Gimbal. It allows for live, switchable infrared and visible video from a FLIR Vue Pro / Tau camera and a GoPro.
The Helium Gimbal features a quick disconnect to easily go from case to f
Read more…Hardware in the loop
I want interfacing APM with flightgear but i success in send from FG to mission planner but cann't send from mission to FG. Please anyone help me.I think the problem in IO protocol in FG.
Read more…