I would appreciate it if anyone could help me out. I am working on developing a basic image analysis application and need some NDVI /NIR and RGB images that i can use for testing and developing. The goal is to eventually develop a low cost image anal
Read more…When I plug in a USB to mission planner my flight controller is functioning fine, but when I disconnect and just run from the lipo the voltage goes down to 3Vdc.I have checked the power module and I am getting 5Vdc output from it.All the rails have 3
Read more…Why is ANTENNA TRACKER now greyed-out in version 1.3.4.0 and 1.3.4.1? It worked in version 1.3.3.9.
I was starting to build my own tracker based on information on the net, but find that option no longer works on version 1.3.4.x
Or am I missing somet
Read more…I know this is a drones forum, I have drones but this is for my full sized aircraft. I built a roll gimbal to do aerial mapping for projects like pipelines, rivers, roads etc.
Aircraft - Pipistrel Virus SW
Gimbal controller - Phobotic Centrepiece HV.
Read more…I connected to Pixhawk controller with some simple code that i wrote ( develop ).
The code read the information that my Pixhawk is sending out.
As far as i know - all the information that the Pixhawk sending is a response to mavlink request from the
Read more…There are two kinds of FPV in the market. One is RTF (ready to fly) UAV which means you can operate it as soon as you get it. Another one needs you to choose and buy body frame, motor, screw propeller and relative electronic component, then assembly
Read more…Good evening. I have a problem. I can move my plate usually by USB. But when I do the communication by xbee, the following mesagem the upload: avrdude: stk500_getsync (): not in sync: resp = 0x00.
How can I solve ?
Hi all I hope this is the correct place to be asking this type of question.I have a fishing bait boat configured as in the title.I have a arducopter 2.6. Not sure is it's capable of working with this configuration.Any advice from you experts with how
Read more…My rig is the following:
DJI F450 frame
DJI E310 propulsion system
4S 5000 mah battery
AUW ~1600g
My quad suddenly jerked when I was about to start my final descent and fell off the sky from a moderate height.
I am attaching a copy of my .bin log. Thanks i
Read more…Hello,
I am trying to figure out how I can send mavlink commands to my SITL environment. I have SITL running on my linux mint VM and I have my own python code generated from mavgen.py which decoded the mavlink messages from SITL.
My SITL experiment is
Read more…3DX Asia Pacific 2016 is held in ShenZhen LongGang on Oct 28th to 30th, it's organizer by ShenZhen LongGang district people's government. And 3DXAP Events organized at three distinct levels, International Class, Asia-pacific experts, Asia-pacific spo
Read more…Just wanted to share this site with anyone that might need coverage for their drone in canada.
http://www.droneinsurancedepot.com/ seems to actaully know what they're doing and they have the lowest prices i could find.
Read more…I'm a newbie on DIY drones, I only bought a brand drone from online shop in the past. Now I plan to DIY a drone , but I don't know how to begin, how to choose the motor, the lipo battery, camera... I want to make a drone have long flight time. How to
Read more…What I am trying to do is use channel 8on APM to activate a electronic switch.I have verified it is working by using Channel10 and can see it operating, but when I assignChannel 8 it does not work at all.I have put CH8 Opt to Relay On/off and alsoAss
Read more…Hi everyone I'm not able to see of loiter mode in mission planner 1.3.41 so anybody can say me how to resolve this issue.Thanks
Read more…Dear all,
I'm facing an issue and wondering why my Battery (6s 12000mAh) supposed to provide a 35mn flight time just gives 20mn (Out of Battery)... Then, Check voltage after landing... 23.24v (50%).
Details:
C Rating is:10
Battery Voltage to failsafe was
Read more…Hi everyone I'm not able to see of loiter mode in mission planner 1.3.41 so anybody can say me how to resolve this issue.Thanks
Read more…Hi i am wondering if it is possible for dronekit is able to pause mission planner mission in auto mode and switch to guided mode then afterwards resume the auto mission ?
Read more…Hello internet,
Quick question, would someone be able to explain to me the FILT parameter in the PIDs for arducopter 3.4.1 and above? Thanks in advance.
Cheers,
Will F
Read more…Hi,
Dear Droners :)
Every thing was OK, copter stays in loiter mode without any problem.
After slight modification, added FPV TX, OSD and LC Filters and Gimbal cpter is flaying away in loiter mode. It looks like it change position very aggressively. GPS
