My APM 2.8 flight controller stopped responding.
I dont remember should the PC make a sound when i connect the APM to the PC, but there is no sound.
There is just one orange stable light and thats it, no blue, no red.
Not reponding on batter and USB c
I flew quite a lot with pixhawk system with various setups and know about connecting devices like sonar, optical sensor or lidar.
I felt confident configuring pixhawk system until recently I have an order to setup a pixhawk drone for autonomous sprayi
Read more…Hi,
I'm selling this RC items because I will focus in multirotors.
1x Skywalker X8 Black (NEW) - 140.00 EUR
1x Scorpion SII-3020-1110KV (V2) + Replaceable kit (shaft and bearings) - 85.00 EUR
2x AERONAUT CAM-CARBON 12x6.5 - 8,00€
1x ALU PRECISION SPINNE
Hi all,
I am using a futaba transmistter and receiver (8 channel). Does anyone know what does each channel do?
Do the channels control pitch,roll,throttle etc.?
Read more…On my second test flight I noticed that the copter was slowly turning without me applying any rudder input. During the first flight this was not the case.
Also, when I switched to circle mode, the front of the copter did not point to the centre of the
Read more…Hi guys!
Does anybody have an idea of how to use TeraRanger with the arduino? I am currently trying to read the values from the arduino but do not know how to. Anybody has a written code that can read what the TeraRanger is reading? I am using a TeraR
Read more…Hi DIY Drones, we'd like to let you all know about the new Helium Gimbal. It allows for live, switchable infrared and visible video from a FLIR Vue Pro / Tau camera and a GoPro.
The Helium Gimbal features a quick disconnect to easily go from case to f
Read more…I want interfacing APM with flightgear but i success in send from FG to mission planner but cann't send from mission to FG. Please anyone help me.I think the problem in IO protocol in FG.
Read more…Hello, All. I would like to flash BLHeli on a BlueESC, by Blue Robotics (www.bluerobotics.com) . That design is supported by TGY/SimonK firmware, through a hardware-specific include file which defines the MOSFET drive pins, phase feedback pins, etc.
H
Before this had happened, i had few flights pretty good with quite good range and nothing problem.
but yesterday, when i try to fly it, I had this random flip, after flying for like 30 seconds in stabilize and then change to poshold, the quad flip and
Do we have a repair kit for antennas? Or a youtube video we can watch?
Read more…Hello, All. I would like to flash BLHeli on a BlueESC, by Blue Robotics (www.bluerobotics.com) . That design is supported by TGY/SimonK firmware, through a hardware-specific include file which defines the MOSFET drive pins, phase feedback pins, etc.
H
Hi all,
I am working on a project involving distance sensors used for avoidance collision and I was wondering if any of you guys have experience with it? I am using the TeraRanger One.
Currently I am facing difficulties on the serial monitor output of
Read more…About two weeks ago I purchased six KDE 4215 motors w/ 15'' duals props, and KDE 55+ XF ESC's, and yes I am running a UBEC because of the isolated ESC's. UBEC is running to main out port 7 & 8 on the servo rail. I purchased these after seeing and f
Read more…Hi all,
We will start to use the new ebee sq. The flight planning software that comes with the ebee is eMotion, and works only on Windows. Has anyone experience with using emotion on Mac with Windows installed on Bootcamp or Parallels? Any input is ap
Read more…Hello all I am new here and to the drone community. I am looking for some help in deciding on which flight controller to go with. I am building a "Tri-Tilt Rotor VTOL UAV" for reconnaissance, also ongoing development project. Maybe some of you can en
Read more…Dear all:I have developed a drone app using o3dr dronekit packages and I can successfully connect to PX4 board. However, I do now know how to show a preview of the PX4 board on my APP.I used the following API but it simply does not work:-------------
Read more…Hi,
I am a student at the University of Nevada, Reno and working with Original Piksi RTK Kit (915MHz) and Pixhawk to get precise positioning as reported by the Pixhawk.
My setup consists of Piksi connected to Pixhawk on 4/5 Serial Port and further the
Read more…please advice me about my workflow to do aerial mapping using UAV
WORKFLOW UAVs AERIAL MAPPING
https://www.sigitriyanto.com/workflow-uav-aerial-mapping/
warm regards,
Sigit
Read more…Hello all I am new here and to the drone community. I am looking for some help in deciding on which flight controller to go with. I am building a "Tri-Tilt Rotor VTOL UAV" for reconnaissance, also ongoing development project. Maybe some of you can en
Read more…