Hi,
Im trying to build a fully autonomous quad which will maintain a certain altitude. I am using an ultrasonic sensor to measure my altitude which will be sent to my arduino. I also have a flight controller(naze32). Im wondering if I can directly con
Hello all,
I have just recently joined this forum and find it fantastic what you guys are doing, very nice job.
There is one question going around in my mind for quite a while now: Why aren't there more single rotor drones out there? Though some posts
Read more…I'm looking for a quad that we can fly indoors to demonstrate our Ground Control Station, the Wing GCS (Image below) We currently test with a bigger quad with 16" carbon rotors, but it's clearly not the sort of thing we can fly around the workshop. I
Read more…Just installed a baro on my cc3d running cleanflight.Is it possible to set a max altitude and/or climb rate?
Read more…Does anyone know where I might find the most basic step by step instructions for using the Tower app? One would think that would be easy to find, but it is not. 3DR provides instructions that dance all around the core such as downloading the app, con
Read more…Greetings! I'm a CS student trying to start a project in AI with drones, and I'm having a rough start with the software I'm trying to use.
I'm using a laptop with Debian 8, I struggled installing APM Planner 2 on my PC due to missing dependencies, out
I am going to compare Autodesk "Site Scan" with Pix4D Mapper.
I can find demo version of Pix4D Mapper. But I don't know how to use demo version of "Site Scan".
Before purchasing software, I want to test them.
Please anyone help me.
Read more…This is my theory:On Basestation only having a M8T Gps and a radiolink to send data to rover.In the rover i have strsvr to feed Basestation data to RTKNAVI.Do you Think this will work?
Read more…Hello all !
I'm trying to get some extra safety features on my hexacopter. I've read that you can connect the APM via USB and have the power module at the same time without damaging the board or risking a brownout.
However, what I am trying to find out
Hello folks!
I've been recently trying to establish reliable WiFi communication between ground station and multicopter's onboad PC (in my case Odroid U4). My target is to have consistent connection between 0.5 - 1 MB/s in radius of 500 meters with cle
Read more…I know about the Gem Fuel Guardian some have referenced on this site but there is little info on it. It's not inside the APM help documents so I assume it has not yet been made to work officially. So at this point in time, is there any way to measure
Read more…I'm working in panorama 360 panorama project, using a 6 x Sony a5100 and 19mm 2.8 f lens.
Anybody have experience in to shoot 6 cameras at same time using Pixhawk ? i have the cable
to shoot one camera from pix.
I assume that the exif geotag postprocess
Read more…Hi can any one tell me why I have the words stabilize come up on my
I am selling custom engraved FAA number tags on Ebay. Check them out here: http://stores.ebay.com/gregs-engraving?_trksid=p2047675.l2563
Read more…I came across an IEEE paper regarding quadcopter failsafes by Mark Mueller in which despite the loss of one or multiple propellers/motors, the quadcopter can still be controlled to the ground.
It's pretty incredible stuff and would be great to see in
Read more…Hi I am looking at purchasing a lawmate 1000mw 1.2-1.3 ghz system with high sensitivity receiver and was wondering if anyone here had some experience with it or similar.
I have a somewhat modified bixler 2 with apm 2.6 915mhz modem, 9x 2.4ghz receiver
Read more…I'm not looking for answers I'm looking for guidance. I'm doing a University quadcopter project, and I purchased a pixhawk for autonomous flight mode and I will be using mission planner. I'm going to use 5 ultrasonic sensors placed on the drone, that
Read more…Hi all!
I've already solved my problem, this post can be deleted since it doesn't provide usefull informations.
Thank you.
