Hi Everyone..,
I want to update this issue. I’m trying to get the serial interface of 3 axis gimbal controls to pixhawk through the telem2 port.
Connecting the gimbal controller serial pins (tx, rx & gnd) to the pixhawk telem2 pins as a below order. Rx
Read more…GPS timer info, received comes from the sats, and works on a 1,024 week cycle. That 1024 week cycle resets back to zero this year on April 6, 2019. Does anyone know if this is going to mess with our standard small gps receivers? As mfr's are not requ
Read more…Hello,
I wanted to ask about the limits of the accelerometer and gyroscope in the pixhawk. I wish to use the pixhawk as a flight controller for a turbine powered plane capable of speeds upwards of 100m/secs.
I know this is a bit much for the poor pixha
Read more…In the cultivation of crops, we pay attention to "three-point, seven-point management." This is also a summary of the practice of the ancient working people in China based on the current production conditions and productivity levels. But nowadays, wi
Read more…Hi Guys,
Today I went through a problem that had never happened before.
I made a mission with points of passage to test the range of my telemetry, the plane did everything right, took off, arrived at the correct altitude until the WAYPOINT 6, after, it
Hello,
I built a basic quadcopter for my first project (following instructions from this instructables page -> https://www.instructables.com/id/Cheap-Sturdy-1-Hour-Quadcopter/) and now I would like to build a hexacopter for my second build, one that
Read more…Dear Forum,
I am very new in drones can you please help me to start.
For my university project I need PC or raspberry controlled drone. We have small budget for that.
Can you please recommend some models which I can buy?
Is there wifi control based drone
Read more…Hello everyone,
I finally finished to construct the ardumower. Compiled the ardumower code with just sonar : the mower have a good behavior.
To go more far i would like to read data (same as when the arduino is connected by usb and we can see values in
I'm working on a 600-frame drones, and I have a problem that does not hover.
It lifts for about 10 seconds immediately after I fully charge the battery. After few seconds, however, even if I raise the throttle to the maximum, it does not hover anymore
Read more…Hey everyone!
I am in the process of making an e-store that sells drones, RC cars/boats/helis etc.
The url is www.rc-central.com. If you wouldnt mind taking a quick look and providing me with some feedback about how i could improve the site, i would be
Read more…I want to control the Dc motor through px4 firmware by controlling the output pwm. Is there anyone who can help me to control the PWM duty cycle ratio order to increase the speed of a Dc motor? or is there any other way to control the speed of Dc mot
Read more…I have build the missionplanner in Visual Studio2017 (Windows 10-64bit) and it has successfully build.
But unable to launch the mission planner and it stopped working during initial launch.
Kindly let me know what can be the issue.
Read more…Hi,
We are using Mapir2 NDVI camera for data collection. Currently we are using Columbus GPS V990 v2 for geotagging. We also have the trigger cable for Mapir 2 camera but not able to use it with the current GPS. Is there any way to use the Advanced GP
Read more…Hello, I am new here. Bought a Pixhawk, switching from a naza m v2 controller. I believe I have everything hooked up according to spec. For testing purposes here I have no power module hooked to the pixhawk, I am powering the board through the ESC's.
Read more…I have a Rover with Qground Firmware with an Original Pixhawk i can drive fine in Manual mode but it says this Vehicle doesnt support This Mode ?
Read more…HI,
I need to extract flight logs from my drone's (DJI Spark and Parrot) black box, I have heard about kind of flasher dongle that has that capability.
Is anyone here know about that thing?
Thxs
Read more…Hi!
Im connecting my pixhawk 2.1 cube to my flir vue pro via mavlink over the serial2 port to geotag the pictures. The Flir has a RX and TX port, so I use that to connect to the Pix.
Using both cables, the geotag works just fine, buy I need to use just
Read more…Hello guys
We are trying to setup a RTK GPS here, but we are stuck setting up the client in Linux. Hopefully someone can drop a tip?
We are using Drotek’s tiny RTK and the TW2712 Tallysman antenna on the drone. The companion computer is a lattepanda r
Read more…I am able to calibrate each of the esc’s individually by connecting them individually to reciever itself directly.But when I try to calibrate all four at once its not happening.I am doing the exact process for calibration as mentioned everywhere, lik
Read more…