Hello everyone,
i want to connect an external force sensor to my pixhawk 4 to log force data.
My force sensor delivers a voltage and i thought i could use the "cap & adc in" - port of my pixhawk to connect the force sensor to and get digital data fro
I have a beginner's question about the power module supplied with my new Pixhawke 2.1 Cube.
I am building a big octocopter and want to set up S4 LiPo battery stacks with multiple plug arrays to plug in 4-6 batteries at once, except the supplied power
Read more…Hi all,
As you're the experts in the drone industry, I don't know anybody better to ask for filling out a quick survey on drone-generated content than you.
The survey will neither assess nor store any of your personal data and will only take about 3 mi
Read more…I am using eCalc to design my first DIY drone. The design goal is a platform for photograghy. I've backed into some of the parts so excuse some of the selections. The motor selection is what is currently confusing me.
The frame is a 450mm so it can
Read more…On running dronekit code v2.9.0 on arduplane v 3.2.1., proper communication link between pixhawk and companion computer is not established and it always shows "command received" and then after a while the program terminates. On looking up in the inte
Read more…Hi! My name is Sarah and I produce “Should This Exist?” a brand new podcast that examines radical technologies, the inventors behind them, and the community who engages with them.
Our next episode focuses on DIY Drones and the community you all have c
Read more…Quick question,
Anybody care to explain how to control relay 1 and 2 by transmitter using rx channels ?
I am currently using apm plane 3.6 for aerial mapping.
To control the camera -a5100- I use aux1 and aux3 as relay 1 and 2 respectively.
Relay 1 trigg
Read more…Hi there, I am new to pixhawk and i want signal from AUX channels of pixhawk flight controller.
I dont know how to access those AUX channels and i tried using the all tips for camera triggering provide on internet but didnt get any signal out of those
Read more…Hey Y'all,
This problem has been plaguing me in the setup of my drone. I cannot get the motor to spin or calibrate my ESC through pixhawk.
The motor makes beeping sounds on startup (4 beeps =4s battery)
I have made sure that my radio is calibrated. It i
Read more… |
|
|
Hello
A few weeks ago I almost accidentally check e-mail in New Atlas about GoFly contest for drone able to carry a man. The contest is sponsored by Boeing with, they say 2 million dollars prize fond. New Atlas had shown 5 winners for the first phase
I built my own controller by using Simulink, and I would like to get local postion of my Quadrotor.
To achieve this, I am trying to use uORB Read Topic block.
I tried three msg file for uORB block, 'vehicle_local_position', 'ekf2_innovations', and 'fil
Read more…Hi everyone
This may already be talked about but here it goes.
I just bought a Sjcam SJ8 and a SJcam gimbal 2. They can both be controlled through android app and the gimbal connects to the camera via bluetooth and then the phone to the gimbal.
This g
Read more…Hi everyone
This may already be talked about but here it goes.
I just bought a Sjcam SJ8 and a SJcam gimbal 2. They can both be controlled through android app and the gimbal connects to the camera via bluetooth and then the phone to the gimbal.
This g
Read more…hello everybody
i want to make a dual operator system as the inspire 2 . I have figuerd out how to do dual op on the storm 32 but i want to have dual cameras (one on the gimball and one on the front ) , i could have a video swich on-board but it woul
Read more…Hi all.
Ive just discovered the herelink and think it would be ideal for my new project. Ive have tried to keep the multicopter shell as small as possible but the herelink air unit is quite large, especially if you have 2 HDMI plugs sticking out of th
Read more…I'm trying to fly the drone X8 + coaxial octocopter, and I've had many problems, it does not rise, it goes sideways or it just takes a 360 degree turn on the ground but it never rises, I'd like to know if you could help me with what version of firmwa
Read more…Hi Everyone..,
I want to update this issue. I’m trying to get the serial interface of 3 axis gimbal controls to pixhawk through the telem2 port.
Connecting the gimbal controller serial pins (tx, rx & gnd) to the pixhawk telem2 pins as a below order. Rx
Read more…GPS timer info, received comes from the sats, and works on a 1,024 week cycle. That 1024 week cycle resets back to zero this year on April 6, 2019. Does anyone know if this is going to mess with our standard small gps receivers? As mfr's are not requ
Read more…Hello,
I wanted to ask about the limits of the accelerometer and gyroscope in the pixhawk. I wish to use the pixhawk as a flight controller for a turbine powered plane capable of speeds upwards of 100m/secs.
I know this is a bit much for the poor pixha
Read more…