Hello everybody. I'm a french bloke living in japan indirectly involved in medical/healthcare.The country as you might know go throught some regular violent weather and common sense is in quite short supply. For example... blood banks are sometimes f
Read more…I've read up on Pict earth through DIY Drones and their website and it would work great for my needs. It seems like their english site is down currently and their french site doesn't list any particulars about pricing. Does anyone currently use Picte
Read more…In this link here:http://diydrones.com/profiles/blogs/using-the-5hz-locosys-gps-withThe code link is broken. Can anyone upload the GPS parsing code?
Read more…i got my easystar ready to fly kit today and i was going to change the motor and other stuff but it appears to be glued together . does anyone know if it is infact glued or is it just stuck. eg. can i pull it a part or is there a trick to get it apar
Read more…Hello,I would like to connect arduIMU to arduPilot.I would like to build a complet system with: arduPilot, arduIMU, GPS, pressure sensor and magneto-sensor.1) Do you think it's possible ?2) Is-it possible to connect them using the pins MISO/MOSI ? Is
Read more…I'm interested in purchasing the parts to build an Ardupilot UAV. I'm trying to follow the manual's parts list, however it says the Shield and airspeed sensor no longer exist in the diydrones store. Sorry if this has already been posted/answered, but
Read more…Hi all,Does anyone have suggestions for traveling by air with your UAV? Packing suggestions to avoid damage? Security suggestions to avoid delays? (I hear that LiPos should be carried on, not checked.)I read Paul's post here:http://diydrones.com/prof
Read more…Hello, hope all is well,> I recently purchased a X-3d BL with the new funpilot (successor to x3D board) and x-acc board> what is the ideal setup to do GPS position hold and waypoint navigation with video?
Read more…Does anyone have experience with these receivers regarding interchangeability between brands, eg Futaba c7 transmitter and cheep off brand receivers such as the RX 2405?
Read more…My project involves engine installation. I am therefore searching for engine installation procedures, please.
Read more…I had order the hardware in mid August and will get them in next month. Don't worry, I am living on the other side of the world and things go very slow here. However, according to the previous main page of the ArduPilot I had opted for the Code 1.x o
Read more…I'm not getting a GPS lock with uBlox 5.I wondered if the checksum comparison (below) is correct as UBX_ck_b is not checked but UBX_ck_a is used twice?Code extract from GPS_UBLOX tab:if((ck_a=UBX_ck_a)&&(ck_b=UBX_ck_a)) //Verify the received checksum
Read more…I'm planning a UAV based on the HTC Dream (G1) and arduino IC.I realise this is a difficult proposition but I think it can be done!The foreseeable problems that I think I'm going to encounter are:- Pitch and roll calculations, accelerometer is built
Read more…Hi everyone.Im trying to get my Ardupilot project up and running - I was going to purchase the Shield kit to complete it but I noticed it says its no longer going to be available. Is there going to be a replacement for it? (maybe this was already add
Read more…At the risk of sounding ignorant . in the case of servo connections on the rc receivers.are the seperate connection only designated for specific servo control and throttle control.ie(rudder,elevator.throttle) are these specific channels or does this
Read more…Hello, I have a problem that my Ardu Pilot board doesn't do anything when I turn the toggle switch. Neither the Mux LED nor the Mode LED ever went on. With the oscilloscope I was able to mesure that a signal is coming in the ATtiny but no matter how
Read more…HI all,I m on developing a GCS on the basis of rotation matrix elements. Is it possible to display the roll and pitch on the basis of rotation matrix at the output . I m using Bill's UAV DEVboard and getting rmat data at output .After little analysis
Read more…Hi, I put together the blimpduino kit but I seem to be having some issues with the behavior the motors and servo. RC mode has been tilting the servo up and down appropriately but the two motors both spin at full speed (I can't seem to slow them down
Read more…Hi allDoes anyone know of any sensors that are small enough for UAV's for such things like sensing water/chemicals on the ground during low level flight?...and where they might be available from, so that I can get some technical information about the
Read more…I have some problems to monitoring for my UAV . Now Im trying wireless communication using Gps (sportTrak, Magellan) and FM transceiver model TG-5A Icron.It is not OK.Please suggest me How to do this communication.I'll add GPS and one ICRON in airbon
Read more…