I set up a taildragger with Arduplane 3.8.3 and Rudder Only mode. As part of the instructions, it says to send the aileron stick signal on my transmitter to the yaw channel. That all works fine, but my concern is that to arm/disarm, I now have to do
Read more…Hi.
I have just built my first quad having installed Pixhawk on board,
Have just flown it for the first time in my small garden. It lifted of really smooth and took it just above fence height to try and keep out of prop wash, had it in Alt Hold and
Hey! I have read a question like this before but didn't really helped me. I would like to know what is the easisest way to send "Roll/Pitch/Yaw/Throttle" and "Flying Mode" commands to a drone from a Raspberry Pi that is connected via Serial Ports at
Read more…Here is the new members of our MAD Components!!New M6 C12/C15~~ Industrial & Agriculture Grade with AMAZING lightweight, which is also dust-proof and waterproof!
Pre-order is acceptable!
If you have any questions covering the products, please contact A
Read more…Hello All,
I am brand new to all this so please bare with me through the multiple questions.
I am building a 4WD rover with FPV video.
Currently I believe I have all the bits, I just need to integrate everything.
The following is a list of my parts;
- Frs
Read more…Just joined this forum and midway through my very first build. I am putting together my quad with Naza M V2 flight controller, 4 Turnigy Multistar 2213-980 kv14 pole Multi-Rotor Outrunners and 4 DYS BHeli30 amp ESC's.Trying to bench test the system
Read more…Hello guys,
Anyone has a good explanation why the area of a polygon created on QGIS is different at the area calculated on MP?
Also, there is a simple way to export directly the waypoints to QGIS?
Cheers and Happy New Year!!!!!
BQ
Read more…Hello, everyone. I am sharing how to connect Benewake TF LiDAR to Arduino.
May this helpful.
Step 1: Hardware Connection
The linear order for the LiDAR products of our company is defined as: red +5V, black GND, green
TX, white RX; the power supply
Check this link to see detailed item
https://www.sparkfun.com/products/14577
Read more…Just dropped a scratch built flying wing from a high altitude weather balloon. Here's quick vid of detaching at altitude.
The glider did the right thing and managed to land on it's own at the target landing site, but while looking at the logs I realiz
Read more…Hello!
I am an amatuer UAV pilot and I am an aviation insurance broker as a profession. My involvement in the UAS industry has contributed to my father's interest in drones. Since I fly DJI products, and he has not flown at all, neither of us have exp
Read more…I have an AMP 2.5 that I am playing around with and would like to know if there is an archive that has docs on the board? Specifically, pinouts but any docs will help. Thanks.
Read more…Hello, I would like someone to help me know how I can build a rc boat using pixhawk to perform bathymetry, I have seen that there are boats that do this work, and I would like to know how to do it, what parts I need, what they are called and where to
Read more…I use an antenna tracker that tracks my apm2.6. I know that now that you can make them so you just put one APM on the tracker and one of course on the craft and it tracks it.
Does anyone know of a phone app that can do the same thing? Like a friend fi
Read more…Hi,everyone
I'm trying to get data from sonar which is connected to "TELEM2" port of pixhawk by serial communication. However, my sorce code doesn't work and I can't see data which is sent by sonar.
My settings are
hardware: pixhawk(it connect to compu
Read more…Hi all, I am new to the forum and about 2 months into a rather large x8 copter. I flew a flamewheel quad to get myself familiar with the mission planner and general drone flying, as i am a fixed wing pilot of 20+ years. Has anyone run a large jeti sp
Read more…I am getting cant locate node error while running mavros
roslaunch mavros px4.launch
ERROR: cannot launch node of type [mavros/mavros_node]: can't locate node [mavros_node] in package [mavros]Hello,
I have a problem with automatic takeoff in MissionPlanner version 1.3.49 build 1.1.6410.20232 with the PX4, version 3.7.1.
If I run with the given 2 m/s, the engine starts but only with about 30% power.
This is of course not enough power and the
I built a copter for a friend, who was out flying a mapping mission in auto. Just prior to the last waypoint the chute deployed. After reviewing the logs I cannot determine why the chute deployed. It looks as thought the copter is flying just fine an
