Has anyone found a good internal-tooth washer and nut to fasten the prop to the motor?
I tried some M5-0.80 hardware from Lowe's based on 3DR's website, but it doesn't seem to fit properly.
http://store.3drobotics.com/products/motor-ac2830-358-850kv-1
W
Read more…I'm guessing it's for the telemetry kit...I thought the sd card that goes in the iris is pre installed.Thanks
Read more…So, the other evening, I decided to do a little flying. The Iris powered up correctly but as it began its ascent, it started spinning and flying out of control. It "landed" via a tree. When I inspected it, I noticed that one of the motors was loos
Read more…Hey everyone, I had a bad crash yesterday. One of the motors came out of the Iris and the whole unit plummeted to the ground. HERE is the video of the crash...The unit is thrashed and the gimbal broke off even though it never hit anything. After insp
Read more…Anyone know of a USA company (i.e., not shipped from overseas) selling a quality FPV package for around $300 that is IN stock...?
To be used on an IRIS using GoPro 3+ as output.
Read more…A public Facebook Page for 3D Robotics IRIS owners to collaborate and socialize. Help each other out and bring forth new ideas and concep
Read more…I would like to try flying with Graupner E-PROP 10x5 and 5mm reduction kit (http://team-blacksheep.com/products/product:123).
But the prop mount of IRIS is too short for the Graupner props. The screws will not fully screw on the mount and It don't tr
Read more…About 10 minutes into my IRIS flight today, and it starts sinking on it's own and lands. Fortunately, i was only about 10' above ground, so it didn't hit too hard. The LED light was steady GREEN the entire time. I rearmed, took off again, and 30 se
Read more…Is anyone else finding that when setting the transmitter to auto and lifting the throttle to start a mission the Iris throws itself forward (or sometimes backwards) before correcting itself and heading towards the waypoint?
-Joe
Read more…Anyone know what size/type of screws are used for the props on the IRIS? I lost one and am grounded until I can replace it.
Read more…I figured it would be nice to have a place that we can post our IRIS flight videos, here is my first entry.
Cheers!
Read more…I bought the Iris as a durable platform for FPV but with my first few flights I have a problem that makes it un-useable for FPV.
In Loiter mode, with the left stick at 1/2 throttle, any forward movement beyond a slow crawl causes the iris to gain alti
Read more…Have anyone experienced this on IRIS?
Circle radius 0 (panorama) rate at 72, IRIS stops circling every 2-3 turns and does a 1/4 circle opposite direction as if it's trying to correct something.
I don't get this at slower rates like 18, 36, 54.
See video
Read more…Setup (All from Horizon Hobby)
| Product | Item Number | Qty | Price | ||
|---|---|---|---|---|---|
| 4400mAh 3S 11.1V G8 Pro Lite+ 25C LiPo | THP44003SPP25 | 1 | $89.99 | ||
| Product | Item Number | Qty | Price | ||
| XT-60 Type Connector Set 3.5mm | INTC23352 | 1 | $3.99 | ||
| Product | Item Number | Qty | Price | ||
| 3S Balance Adapter TP to JST XH | THPAL3S | 1 |
Has anyone considered or tried 11 inch props on the Iris? What about 3 blade or 4 blade props?
Read more…I'm looking into either finding or having a case made that fits the IRIS with props without the transmitter, with a custom cut foam interior. This case would also have room for 3 batteries and extra props etc.
The dimensions that I am looking at are
Read more…Here's the specs for the "Li-Po Power Pack" that comes with the Iris.
Now look at the "Kokam SLPB8643128H5"
More power, smaller
Read more…Is there any information /why 3DR still delays the shipping of IRIS to Europe?
They do not respond to Emails.
Unmannedtech just tells:
Since it is imperative when planning auto missions to know your flight times I have been testing with stabilize/loiter hovers and measuring air time while I familiarize myself with the Arducopter platform.
I now have 17 full flights with respect to ba
Read more…I have been working-out a few problems before mounting my Gimbal. I would like to do this now but I did not find any instructions on doing this. Can anyone tell me where the wires go that are coming from the Iris? and any photos would be great, a
Read more…