I got iDroneCtrl [a limited but growing GCS for iOS devices ] and it works really solid and seems very intuitive. I created a mission and it worked flawlessly. I think I might have to get an iPad just for this. It plugs directly into the lightning co
Read more…Hi, friends.
I have aquired a Pixhawk 3DR in last December and, til now I have test bench only, installed on an Anaconda plane.
I have Mission Planner 1.3.27 and APM V3.3.0 installed on a Win7 computer.
Today, when I powered everything as usual, I have
Read more…This is my first Pixhawk build.
Pretty much have a Jazzy wheelchair subframe set up in skid steer.
Using a 2x32 Dimension Engineering ESC in "independent channel" mode.
Using a low cost 6 channel E-Sky radio and receiver.
I can successfully drive the rov
Read more…Dear all,
Since I tryied to install MinimOSD v1.1, my Gopro is not anymore self powered by my Lipo (4s)
Please find below wiring strictly respected
Will appreciate any advises and/or experiences
Respectfully
Read more…I have recently assembled and flown my custom designed Y6 hexacopter but have found that there is a lot of pulsing going on in position hold mode. Does anyone have any ideas on if this is an ESC issue or can it be tuned out with the Pixhawk? The hexa
Read more…Thanks for adding me to the group!
I read a really good thread recently about using a Stratosnapper V2 IR trigger with the Pixhawk to operate my camera, but I wasn't exactly sure about how they were powering the Stratosnapper's IR transmitter. The di
Read more…Hello,
I've just got my first pixhawk after building a few UAVs with apm 2.x boards.
when using the apm i used to download the dataflash logs (the on-board logs) and analyze them, specifically the cpu performance monitoring values (to check and compare
Read more…For people who participated in development of autonomous flight using Pixhawk.
I wish to collect some statistics: Where your code is located?
1) Inside the Pixhawk's firmware.
2) The whole code is running on external computer.
3) On both sides.
Read more…Channel 5 seems to be locked in for the flight mode switch. I have a Turnigy 9X with a XJT module. My flight modes are set on channel 6 and I can't figure out how to switch Pixhawk to use channel 6.
Any help would be appreciated,
Tim
Read more…Hello,
I have an issue with a new quad running Pixhawk.
Upon taking off this morning, the quad immediately started to yaw in circles while hovering. The yawing stopped after roughly 10-15 seconds and then flew perfectly. I have noticed in one prior fli
Read more…Channel 5 seems to be locked in for the flight mode switch. I have a Turnigy 9X with a XJT module. My flight modes are set on channel 6 and I can't figure out how to switch Pixhawk to use channel 6.
Any help would be appreciated,
Tim
Read more…I have built a S550 Hex running Sunnysky 3108 720kv motors. I have a UBEC in channel 8 and all ESC's have all three wires connected to the Pixhawk. My Pixhawk is brand new.
The Spider 30A ESC's calibrate fine and do not exhibit any throttle issues in
Hello again,
As I've yet to get much a response on previous post regarding a pixhawk which has the error code "Radio control not active", however it is most certainly active. as I can connect a motor to the 3 pin slot on my X8R and can sing the motor
Read more…Hi all,
I have troubles with my first build - the quad flips forward
Here're the build details:
Pixhawk clone (HobbyKing)
DYS Quanum 3508 700kv motors
Steadidrone Dash frame
SkyWalker Quattro 25A 4 in 1 ESC
12x3.8 SF props.
4S lipo
I have done the following:
-
Read more…Someone can confirm me if this Pixhawk is original from 3DR?, It's easier for Us to buy in china than in the USA.
http://www.foxtechfpv.com/pixhawk-915mhz-combo-p-1895.html
Read more…Getting tired of waiting for my replacement stock Radio from 3DR for my Iris+. I have a brand new very lonely Spektrum DX6 in the box. I believe I will have to get a receiver...as I bought it without. Has anyone used this TX with the PIXHAWK? If so a
Read more…Radio calibration page see's full right yaw input but pixhawk doesn't or barely responds. If somebody could look at this log I would really appreciate it.
Read more…On last days I listen some comments from APM-Pikhawk users about vulnerable wires and connectors for GPS, RM, etc. on my oun, I experienced failed gps wires from new (original) and RM one with some flying time and saw others with "NO GPS" problems, t
Read more…Hey guys,
First time posting something here! Thanks in advance for any help!
Background: I'm working on a senior design project to create a motion sensing board that will act as a controller for a quadcopter. So when the board tilts, the quadcopter til
Read more…hey guys, flashed my pixahawk using mission planner then calibrated the compass and the accelerometer and then flew in auto trim mode after which i connected the pixhwak and noticed that when i put my quad on a level ground the mission planner showed
Read more…