About

Gender

Male


Location

Budapest


Please tell us a bit about your UAV interest

Developing drones and UAV


Hometown:

Budapest


Activity Feed

Gabor H replied to Nichon's discussion tarot t4-3d gimbal compability with pixhawk in ArduCopter User Group
"Hi,Any update for the topic maybe?I'm also interested about a solution."
May 24, 2016
Gabor H commented on Darrell Burkey's blog post Mapping Rural Australia
"That's sounds good. Just asked because I'm in a planning phase of mapping project, and one of the potential aircraft is a flying wing. Curious, how's a flying wing perform in summertime, when there's strong thermal activity, with visible cumulus…"
May 20, 2016
Gabor H commented on Darrell Burkey's blog post Mapping Rural Australia
"What was the percentage of failed images, due to no gimbal on board?"
May 20, 2016
Gabor H replied to Oleksii Svyryd's discussion Mapping plane frame
"Don't forget about check this one, too.Pretty big inside, Sony A5000 can fit. Myself going to choose this one soon.http://flyingwings.co.uk/new-products/venturi-fpv-wing.html"
Apr 29, 2016
Gabor H replied to Cala's discussion Aerial Photograph for agriculture purposes
"Hi Guys,
I'm new to this NDVI imagery. Therefore asking "dumb" question. How do you apply spraying corrections to the mapped fields when you've an analyzed NDVI map? How will farmers apply additional fertilizer on the filed? From farmers side a GPS…"
Apr 26, 2016
Gabor H posted a discussion
Hi,If I know well multi engine with Pixhawk/Arduplane is not possible till date.When will Arduplane able to handle at least twin engine aircraft?Regards,Gabor
Feb 22, 2016
Gabor H replied to Paul Hansel's discussion X8 Stall/Spin Crash Stories, and how to prevent them. in X8
"That's bad.
I saw on anotherd build that someone using slats on 1/3rd area of the leading edge, counted from the wingtip."
Feb 22, 2016
Gabor H replied to Paul Hansel's discussion X8 Stall/Spin Crash Stories, and how to prevent them. in X8
"Hi,

How about adding wortex generators through the whole wing to avoid stall and spin?
Would that help?"
Feb 22, 2016
Gabor H commented on Gabor H's blog post Galileo arrived with recent FW update for u-blox 8 series users
"For GALILEO you need to be lucky. With only 7 SV's online, there's a window when no GALILEO visible.In CEE region now 0 GALILEO is visible, but 4 BEIDU is visible. Check the prediction on the radar, more less…"
Feb 20, 2016
Gabor H replied to Cala's discussion Graphene batteries in ArduCopter User Group
"Cala,It's very well overrated. As many Chinese origin batteries used to be.
If the Power Modul telemetry values are real values(had no chance to measure it by instrument), my copter draw about 12-15 amps on climb and hover.
And the green MultiStar…"
Feb 11, 2016
Gabor H replied to Cala's discussion Graphene batteries in ArduCopter User Group
"Hi,Same experience with HK MultiStar. Same Y6 copter, and final rsult that I had to ditch these batt to the waste bin. Need to buy much higher quality 6S batt.It's cheaper to buy high quality 6S than rebuild the copter from a massive crash."
Feb 11, 2016
Gabor H replied to Dmitry Prokhorov's discussion Solution proposal for PixHawk IMU2-related BAD ACCEL HEALTH
"Ok, thanks for the update Dmitry!"
Feb 7, 2016
Gabor H replied to Vesselin Goranov's discussion Upgrade to 3.3.2 - Alt Hold rising full trottle up
"Hi,
Thank you Vesselin to looking into the log.Copter is tuned, but not with the autotune function. It flew stable till the crash.Don't know why the SAT number dropped to 7. Maybe it's due to the quality of the GPS. It's a Chinese copy, mass…"
Feb 7, 2016
Gabor H commented on Gabor H's blog post Galileo arrived with recent FW update for u-blox 8 series users
"Bernardo,
I've GPS+SBAS+GALILEO+GLONASS enabled, and I can set the highest rate of 80ms/12.5 Hz in u-center.So it look like the measurement frequency rate is not locked to 3 Hz."
Feb 5, 2016
Gabor H replied to Vesselin Goranov's discussion Upgrade to 3.3.2 - Alt Hold rising full trottle up
"Hi,I had just today chance to try the Pixhawk with the changed sponge to a more thicker piece of mat.2 flight went good. But the 3rd one, the 2nd part of it, looked like when a machine lives it's own life.Speeded up itself, went into a massive dive,…"
Feb 3, 2016
Gabor H commented on Gabor H's blog post Galileo arrived with recent FW update for u-blox 8 series users
"There are two download links on U-center's webpage!
The big red "download" button will download v8.18
There's a .zip link at the bottom of the page, that will download the newer v8.20. "
Jan 27, 2016
More…