Gender
Male
About
Location
Eindhoven
Please tell us a bit about your UAV interest
Flying an FPV plane and a Discovery-style quad right now :)
Hometown:
Eindhoven
Activity Feed
""added SBUS FrSky telemetry support"
That should probably read: "added FrSky S.PORT telemetry support""
That should probably read: "added FrSky S.PORT telemetry support""
""Always keep your aircraft in sight, where you can see it with your own eyes – not only through an on-board camera, monitor or smartphone."
Interesting truth matrix is derived from this line.
You can interpret this like so:
- If there is a direct…"
Interesting truth matrix is derived from this line.
You can interpret this like so:
- If there is a direct…"
"I can a see a small part of my airframe in the corner of the FPV image in my goggles, does this pass as 'viewing the aircraft at all times'?"
"Thanks, I found the schematic and your explanation matches exactly what I see there, thanks. I was wondering, could it be that the two loads are pulling a too high current from the TXD port (brown out) which could be solved by just placing a 100 Ohm…"
"Hey thanks, great that you found a solution and took the effort to comment here. Could you be so kind to give a little hint as to how things should be wired up? I will definitely try out what you you did and post back the results when it works :)…"
Hi all, hope somebody can shed a light on my problem.I have been flying 2 quads and a Skywalker for 1,5 years and many hundreds of flights with APMs and never had a problem. This time though, I can't get my head around what is going on.I have…
"How can I enable PPM on this board?
There are 4 solder pads near the input connectors that have the "PPMEN" marking next to them. 1 of them seems to be connected to IN3 via a 1K resistor, two other ones are connected to GND and the 4th I don't know.…"
There are 4 solder pads near the input connectors that have the "PPMEN" marking next to them. 1 of them seems to be connected to IN3 via a 1K resistor, two other ones are connected to GND and the 4th I don't know.…"
"This weekend I bought a Teensy 3.1 from the Arduino booth at the maker faire I was flying drones on :)
Yesterday I wired it to my OpenRLSng but failed to get telemetry info on my Taranis. So I just wanted to check some things:
The Teensy flashes…"
Yesterday I wired it to my OpenRLSng but failed to get telemetry info on my Taranis. So I just wanted to check some things:
The Teensy flashes…"
"Great, will keep an eye that!"
"The hardware mod should still be done yes, but the protocol still needs to be either FrSky or SmartPort, since those are the two options the Taranis understands. Therefore, the OpenLRSng RX (or TX, depending on transmission rates) will need to do a…"
"I think this should be ported to OpenLRSng. To have an LRS with native APM telemetry on my Taranis would be fantastic."
"I am going to try this setup with OpenLRSng, since it supports 2-way communication while it can emulate FrSky telemetry on the downlink. It would be great to have an LRS solution with built-in telemetry, especially since I own a Taranis and the…"
"APM:Copter 3.1 is released! Flashing time :D"
"diydronesnews.com, that one was pretty obvious right? ;)"
"That is great news JJ! Thanks for taking this up, it will surely be appreciated!"
"Ah cool thanks, so indeed more than 10% of your visitors are viewing it on their mobiles. For those, DIYDrones offers a "mobile optimized view" (try it!). It is very limited, I can't even write comments on Blogs there.
Not only do I think that…"
Not only do I think that…"
