APM 2.60 Downgrade
Does anyone know how to downgrade from APM 2.60 back to APM 2.50 using the mission planner?
I have tried using arduino to reload the 2.5 like the old days but receiving multiple compile errors.
Read more…Joe's Discussions (35)
Sort by
direction velocity winds aloft
In 1.2.6 the vel and dir display worked properly.
I am currently using 1.2.7 and the dir/vel readings are zero any thoughts?
Read more…Jumpy Airspeed
Anyone know how to dampen the airspeed indication on the mission planner?
While flying the airspeed indication slews +- 10-15 mph. For example when stabilized at 25mph the airspeed indication jumps around from 12 to 37 mph but if averaged the airspeed
Read more…Not getting any AMP data
Hi,
Just curious if the Amps readout is functional at this time?
I am not able to get anything other than a zero after running the motor at 40% throttle for an extended period of time.
I am using version 1.3.16
Everything else works (beautifully!), Bat
Read more…AttoPilot 90A/50V Voltage/Current Sensor
Hello,
Has anybody had any success with the AttoPilot 90A/50V Voltage/Current Sensor as described in the instruction wiki?
I am able to get the voltage portion portion working via AN0 but have kinda ran into a brick wall regarding the current sensing
Read more…Need some help with the current sensor.AttoPilot 90A/50V Voltage/Current Sensor
Just received and soldered up the AttoPilot 90A/50V Voltage/Current Sensor.
To keep things in perspective for the past three months I have successfully been using Bat monitoring for a three cell lipo using the three 3.9kohm resistors provided with the
HKGCS Very Nice!
Hello,
Just wanted to thank Happy and Mr. Levine for the work on the GCS, it works and looks GREAT!
Happy, I have all the functions working (airspeed, target altitude, ect.) properly.
Really like the yaw instrument that displays magnetic heading, an
Read more…APM 2.xxx and HK's GCS=Perfect Mission!
Hello,
Thanks again to all the people involved in the APM.
Today had very good success with APM and HK GCS.
Considering the airframe is an EasyStar, I encountered fairly strong/gusty winds, estimate 10-15kts.
Mission consisted of 13 waypoints with diffe
Read more…HK GCS Airspeed
Hello,
I am not able to read airspeed with the latest version of the GCS. 1.2.109
Airspeed tests ok in the CLI.
Is there an option in the GCS to enable airspeed?
Thanks
Read more…
Where Should It Go?
Grettings,
Referencing the included APM Planner screen shot and awesome graphics.
Scenario-
- Launch the plane in MANUAL mode.
- Switch to STABILIZE mode for a a minute or two.
- Switch to AUTO when plane is positioned as shown in the graphic.
Question
Read more…HK GCS 1.2.75 Lockup
As always thanks for the APM and GCS programs!
I understand APM 2.xxx software is Beta.
Just making sure I'm not making an obvious mistake.
Also posted in APM ISSUES section.
Just wondering if anyone else is having lockup issues with the latest versio
Read more…APM Mission Planner/Autodetect
APM Mission Planner 0.4.20
Thanks for the Planner!
I downloaded and installed the latest APM firmware via the planner, worked great!
All sensors mentioned are the ones suggested in the APM manual and purchased from DIY Drones.
I have airspeed, UBLOX,
Read more…Thanks again HK!
HK thanks for working the airspeed indicator issue seems to work again with APM 2.0.12.
Also I followed some of your posts on TOF regarding UBLOX reporting the # of SATs on the status page. Got it working by enabling NAVSOL in the messages view. Than
Read more…HK GCS Battery Display
Hi,
I am having trouble getting the Battery value in the Status page to display correct values.
I am using a 3 Lipo.
I either get 3.8v or 0.25v.
With previous versions of Apm and HK GCS this function worked properly.
I was not able to get APM 2.0.12 to
Read more…Oilpan TelemPort pin values
Hello,
With the APM and Oilpan operating normally what voltages should be present on the TelemPort pins on the oilpan when referenced to ground without the DIY Drones XtreamBee interface Board connected?
These are the values I am getting,
GND to
Oilpan TelemPort pin values
Hello,
With the APM and Oilpan operating normally what voltages should be present on the TelemPort pins on the oilpan when referenced to ground without the DIY Drones XtreamBee interface Board connected?
These are the values I am getting,
GND t
HK GCS funtions?
Hello,
HK, once again thanks for the awsome GCS!
Just a few questions regarding the GCS and APM 2.012
I understand that APM 2.012 is beta but I am curious if anyone is having luck with these few issues.
I just want to make sure I am not missing somethin
Read more…APM and Magnetometer
Does the DIY Drones magnetometer when incorporated with APM 2.XX actually assist in the navigation equations during low ground speed operations or is it strictly used for GCS/OSD mag heading displays.
Read more…APM/Magnetometer
Hi,
Does the DIY Drones magnetometer when incorporated with APM 2.XX actually assist in the navigation equations during low ground speed operations or is it strictly used for GCS/OSD mag heading displays.
I am not the best at interpreting code, other
Read more…HK GCS BATTERY DISPLAY AND APMv2.01
Hi,
Once again thank you HK!
Trying out the 2.01 APM with HK GCS v1.2.43
I am probably missing something or possibly this is not working due to the APM being BETA.
The GCS is only displaying the voltage of one cell. 4.13v
The proper voltage(s) are displa
Read more…