For sale:
- 3dr GPS module
- Ardupilot 2.6 autopilot
- Hexa Frame(with a few broken legs)
- diydrones Motors/props (860kv motor)
- Spektrum DX6 transmitter
- Spektrum AR6210 reciever with satellite
- diydrones Power Distribution board
- 2 xbee (433mhz) wit
Read more…Hi, the store doesn't carry the diydrones sonar sensor any more.
Does anyone have a link where I could purchase it?
Thanks.
Hi, I just purchased a pixhawk, but decided I'd go ahead and try out my APM2.6 first since it's been collecting dust. I'm using the 3dr Hexa frame.
I've flow rc planes and variable pitch helicopters, but have no experience with multi-rotor copters o
Hi,
I ordered a pixhawk and emailed support to check hte status of my order, but haven't got a reply. I'm surprised there isn't a link to the tracking number on the order page etc.
Also, I can't find some products in the store. The links throughout
Hi, I need another one of these 20amp 3d robotics ESC's(see image).
Does anyone know where I can order one or find the equivolent? It reads DDT-30A-20. Any ideas?
I'm selling my DIYDrones hexa-copter kit and other electronics I purchased for it. I just don't have the time to finish it right now.
Items for sale(all these items are new, never been used):
- ardupilot-mega 2.5 with GPS - $160 shipped [ SOLD ]
htt
I purchased this kit with the larger motor/prop sizes. Does anyone know what the payload is?
The goal is to attach telemetry as well as my canon 60D and video tx. Will I need arm adjustments and motor upgrades to achieve this?
Thanks!
Read more…I have tried everything and I can't get my servos to do anything. I just got the board a couple weeks ago and hadn't had a chance to mess with it until now. The servos work fine when plugged directly receiver but when APM 2 is plugged in they do noth
Read more…Does anyone know of any good quality small cameras that will output SD video while recording HD video(Like the gopro).... I would like to set up stabilize and PTZ(I believe APM and APM 2.0 can stabilize)
But I need to find a camera which has high qual
Read more…For those of you already using the Ardu-pilot Traditional Helicopter, I have a few questions.
1. Can it be used with a flybarless Helicopter?
2. If so, does it compare to the other FBL control systems out there(Only talking about stability, no autonom
Read more…Developers, was wondering what the chances are of releasing a groundstation for android or iphone tablets(maybe phones too)?
Also, what is everyone thoughts on the new google chrome OS?
Request a free Chrome OS notebook here https://services.google.co
Read more…I'm currently testing APM at my desk using an elevon setup. Currently, I am only using a 2 position switch, 1 position being manual, and 1 being stabilize. Dx6i default settings for plane.
When in stabilize mode, moving the APM/Shield works correctly
Read more…Can APM be programmed for non-standard yaw control? Of course it can be, but how hard will it be?
What all additional things will I have to do if using a 6 cell battery. I'm assuming I cannot use APM to monitor voltage. It is also higher voltage than AMP can handle. I'm sure the reciever would put out less though? I'm just a little confused about
Read more…Where can i get the connector on the end of the ftdi cable? I would like to have a cable with this connector on both ends which would connect the xbee to the APM without using 4 separate wires(instead i want 1 4 conductor wire). This will make things
Read more…If i'm flying a plane w/out a rudder, I could hook up the rudder to a PTZ camera(pan). This of course would work just fine for panning the camera.
Haven't seen much about this mentioned on the website yet. I did see one person throw one up for sale with no replies. Looks like it would give ranges farther than 1.3, 900, 2.4 etc. It requires a HAM license, but that doesn't seem like it would be h
Read more…Is there a recommended GPS unit for UGV's? Does the IMU work well enough with regular GPS modules to keep a vehicle on the road?
I'm just wondering if i were to program a rc car to go around a large track, what would i need so that it would not go off
