About

Gender

Male


Location

İstanbul


Please tell us a bit about your UAV interest

I'am currently building a two propeller vtol (please see my facebook profile for photos of the vehicle).


Hometown:

İstanbul


Activity Feed

Öncü Kayalar replied to Vincent Mees's discussion Arducopter in the air with mikrokopter frame.
"Mees,

What is your arming procedure of escs?"
Oct 19, 2010
Öncü Kayalar posted a blog post
Here is the first real flight video of our quad:- APM+OilPan- Mikrokopter Frame (50cm)- Turnigy 2217-20 motors- Electrifly SS-35 escs- APC 10x4.7 props- Zippy 3S 2200mAh 20C- Align 500 landing skid
Oct 17, 2010
Öncü Kayalar replied to Vincent Mees's discussion Arducopter in the air with mikrokopter frame.
"Mees,

I have the same frame. I tried KDA 20-22L and Turnigy 2217-20 with APC 10x4.7 propellers. It is very stable with Turnigy using default PIDs but unfortunately I could not find a stable interval with KDA. I belive KDA 20-22L does not enough…"
Oct 16, 2010
Öncü Kayalar replied to Hein's discussion PID Tuning on your ArduCopter
"Tom, I did fly with default PIDs. If you can write details of your quad (weight, distance between motors, motors etc.) we may help you."
Oct 12, 2010
Öncü Kayalar commented on Stephen Carlson's blog post Aggressive Quadrotor Maneuvers
Oct 11, 2010
Öncü Kayalar posted a discussion
Hello,I am planning to build a mini quadcopter. The specifications will be:- Distance between motors: 30cm- Prop size: 8x3.8- Total weight: 500 - 650g (depending on motor and esc combination)I am not sure which motor + esc combination to use. My…
Oct 11, 2010
Öncü Kayalar commented on Marko Kleine Berkenbusch's blog post Quad position hold with mouse sensor - some details
"@Geoffrey - Thanks for pointing out the work of Javaan Chahl and Sean Humbert. That may be the way to go in the future. Did you see any work using fpga chips for optical flow?"
Oct 8, 2010
Öncü Kayalar replied to Limebear (Rob)'s discussion Blowing up boards by connecting battery and USB at the same time.
"I did it many times and nothing happened.

Once I connected a esc to the board when the battery plugged in. Esc connector began to smoke and I pulled it immediately. Luckily both the board and the esc was not damaged. Only the connector was slightly…"
Oct 8, 2010
Öncü Kayalar commented on Marko Kleine Berkenbusch's blog post Quad position hold with mouse sensor - some details
Oct 8, 2010
Öncü Kayalar commented on Marko Kleine Berkenbusch's blog post Quad position hold with mouse sensor - some details
"I agree, we have to find or create an open system..

By the way I found these when searching an camera based rangefinder:

http://www.asl.ethz.ch/education/master/mobile_robotics/Exercise_3...."
Oct 7, 2010
Öncü Kayalar commented on Marko Kleine Berkenbusch's blog post Quad position hold with mouse sensor - some details
"Here there is a description for Flymentor 3D:

http://www.helipal.com/kds-flymentor-3d-auto-stabilizer.html

What is Positioning Mode?
In this mode, there will be solid green light on the Flymentor Mixer, the CCD Camera and the 3-Axis Gyro are both…"
Oct 7, 2010
Öncü Kayalar commented on Mario's blog post I was already crazy...DIYDRONES made it worst ! The story...part 2
"Hello Mario,

Where can I find that pinion gear on the servo?"
Oct 6, 2010
Öncü Kayalar commented on Marko Kleine Berkenbusch's blog post Quad position hold with mouse sensor - some details
"An approach like this (downward facing camera) can solve the problem of constant velocity translational drift. But a range finder is definately needed for aerial usage."
Oct 6, 2010
Öncü Kayalar commented on Marko Kleine Berkenbusch's blog post Quad position hold with mouse sensor - some details
""Are you sure to fly?" :)"
Oct 6, 2010
Öncü Kayalar commented on Marko Kleine Berkenbusch's blog post Quad position hold with mouse sensor - some details
Oct 5, 2010
Öncü Kayalar commented on Marko Kleine Berkenbusch's blog post Quad position hold with mouse sensor - some details
"@Geoffrey - Why not use a laser beam and dedector other the the wavelenght of the sun?"
Oct 5, 2010
More…