About

Gender

Male


Location

Dublin


Please tell us a bit about your UAV interest

Still a beginner, looking into wider applications of UAVs


Activity Feed

Rohan Jain replied to Rohan Jain's discussion a lost soul in the world of hexacopters. N00b alert. in ArduCopter User Group
"Hi Everyone, 
I just wanted to thank all of you for all the assistance with my hardware issues, which now stand resolved.
I was working on this project to analyze the feasibility of a business based on UAV solutions.
Please read this…"
Jul 24, 2013
Rohan Jain left a comment on ArduCopter User Group
"Hi everyone, please spare a moment to look at this post. http://diydrones.com/forum/topics/guaging-diy-community-interest-in...
I'm trying to get an idea about the kind of interest the DIY community would have in consumer applications."
Jul 24, 2013
Rohan Jain replied to Rohan Jain's discussion a lost soul in the world of hexacopters. N00b alert. in ArduCopter User Group
"All other issues resolved.
Thanks for all the support everyone.!!
Last question:
If anyone is using the 3DR micro CCD camera (3 pin output), and a TS352 Video transmitter. could you give me the wiring diagram for hooking the two of them up directly,…"
Jul 12, 2013
Rohan Jain replied to Rohan Jain's discussion Hexa-c RTF firmware in ArduCopter User Group
"have the RTF from 3drobotics"
Jul 11, 2013
Rohan Jain posted a discussion in ArduCopter User Group
Hey ,I uploaded 2.9.1b Hexa copter firmware on my RTFDoes anyone have the latest dump of the firmware that comes preloaded on the hexa RTF?Would be great if i could know what the differences between 2.9.1b and the preloaded firmware is.
Jul 11, 2013
Rohan Jain replied to Rohan Jain's discussion APM 2.5, COMPASS INIT ERROR in ArduCopter User Group
"Additional info:
When trying live compass calibration, on MP GUI,
I move the APM around fr 60 seconds.
in the end get a message, not enough data in the logs.
Tried accel calib in MP GUI, hangs after saying "Place APM level and press any key"
tried…"
Jul 10, 2013
Rohan Jain posted a discussion in ArduCopter User Group
Hey everyone,I got the Hexa-c RTF from 3drobotics.comhave, APM2.5,loaded with 2.9.1b FW,  taoglas GPS unit, and all the regular stuff.I was setting it up following the first steps guide. and couldn't do Radio calib in GUI, the accel calib, compass…
Jul 10, 2013
Rohan Jain replied to Dave Hicks's discussion APM 2.5+ No dataflash inserted
"Hey,
I'm using an APM2.5 running arducopter 2.9.1b frmware for my hexa-c RTF from 3drobotics.com. Have a taoglas GPS module on it.
the board powers up fine, and i was able to do ESC calibrations, but can't arm the motors.
noticed that on connecting…"
Jul 10, 2013
Rohan Jain replied to Rohan Jain's discussion a lost soul in the world of hexacopters. N00b alert. in ArduCopter User Group
"I forgot to mention this,
Whenever i connect to the APM in CLI,
i get this message:
"3No Dataflash Inserted3COMPASS INIT ERROR"
tried running test/ins command in CLI just now. 
It says "INIT Gyro". But after that nothing. Waited 10 minutes now.
Also…"
Jul 9, 2013
Rohan Jain replied to Rohan Jain's discussion a lost soul in the world of hexacopters. N00b alert. in ArduCopter User Group
"Issue now:
Arming!!!!!!
in MP, set all modes on stabilize.
ESC calibration went smoothly.
tested motor's response to throttle during second last step of calibration.
Unplugged Lipo.
Reconnected, moved yaw to right/throttle down hold for 4 seconds.…"
Jul 9, 2013
Rohan Jain replied to Dave Kellum's discussion Yet Another Noob Who Can't Arm Their Motors
"hey I'm having this issue too.
Tx,Rx setup correctly. ESC calibration went alright.
Could move throttle to control motor speeds.
unplugged the battery
plugged it back
pushed rudd left/low throttle for 4 seconds
tried increasing throttle..…"
Jul 8, 2013
Rohan Jain replied to Alex Wilson's discussion Flight Planner Not Recognizing RC Input
"Bloody hell, I have the exact same issue. To the letter.! Tested my RC Rx by connecting directly to ESC. Works!
but radio config doesn't work.
Tried CLI mode same error as yours.
3No dataflash inserted3AP_Motors: failed to create the throttle…"
Jul 8, 2013
Rohan Jain replied to Rohan Jain's discussion a lost soul in the world of hexacopters. N00b alert. in ArduCopter User Group
"Thanks for all the inputs guys,
Got the DX8 and AR8000 setup correctly.
Tested by plugging in one of the ESCs into the throttle port and running the motor. Works well.
But, i have it all connected to the APM now as per the directions on…"
Jul 8, 2013
Rohan Jain replied to Rohan Jain's discussion RX8 radio callibration
"Have confirmed that the receiver is working by connecting 1 motor to the throttle channel of the receiver. I move the sticks and the motor moves.
The Rx is connected to the input pins on the APM according to the guidelines at…"
Jul 8, 2013
Rohan Jain posted a discussion
Hi,I'm using a 3DR hexacopter frame and motors, APM2.5, Spektrum DX8 Tx and AR8000 Rx.Managed to bind the Rx and Tx with instructions from the manual.Found out that it has to be on airplane mode. (any1 ever flown a hexa on heli mode?)So selected new…
Jul 8, 2013
Rohan Jain posted a discussion
What exactly can i do with the mission planner if i don't attach the ground module of the 3DR radio to the computer using an FTDI-USB cable. (consider that the air module is attached to APM.)The things i know of are the things that can be done when…
Jul 7, 2013
More…