Gender
Male
About
Location
Panacea, FL
About Me:
I own a machine shop in Nth Florida specializing in the manufacture of silencers for firearms
Please tell us a bit about your UAV interest
I am interested in gps controlled flight for aerial mapping
Hometown:
Panacea
Activity Feed
"Downloaded 1.2.83 from archive and loaded, reloaded backup config files for my quad. Big lesson learned today. Change is not always good. lol
thx for all the input "
thx for all the input "
"I have no menu items down the left side when clicking the configuration Icon at the top other than Planner. Its continualy trying to download and update firmware. I seem to have no access to the settings in the quad.
WTH is going on here, does it…"
WTH is going on here, does it…"
"I was using mission planner 1.2.83 build 1.1.5063.12264 before accidental upgrade"
"well more than a little disappointed, was just in a clean hover at about 15 foot altitude, pulled switch for loiter quad flipped up side down and slammed into ground, broke a carbon fibre arm and exploded about $100 in props. I am not at all…"
I have avoided updating mission planner for over two years since everything has worked flawless for what I use my qaud for. Somehow this morning while launching mission planner from desktop it has updated to version 1.3.46. I am having a never…
"I think this is wonderful, I use one to check gates almost a mile away here on our farm. I do have to wonder where all the control freaks are screaming about commercial use, faa certification, los and ama ."
"WHile trying to attempt firmware update, Laptop recognises Arduio Mega 2560 on com 11. choose com 11 from pull down, baud rate is set to 115200, I have not clicked connect. Download firmware, click pic of the quad. Status bar scrolls across a total…"
Is there anyway to salvage an apm 2.5 board that will not connect?I have one of the HK 2.5 boards in a quad that has somewhere around 40 flights behind it and has been rock solid. Today I flew an auto flight, returned no isuue. I swapped batteries,…
"I have begun setting up apm2.5, I have loaded ardupilot 2.74b.
Transmitter is 9xr with dragon link. I have calibrated receiver, been thru bind process . Set elimits to on, set channel 3 (throttle) to -125% , calbrated radio and it show pwm of 910 on…"
Transmitter is 9xr with dragon link. I have calibrated receiver, been thru bind process . Set elimits to on, set channel 3 (throttle) to -125% , calbrated radio and it show pwm of 910 on…"
"I have verified again that when the transmitter is shut off my throttle output channel 3 is dropping to 910 but the apm is holding throttle at the level its at on signal loss and centering the other channels"
"ArduPlane:FS_SHORT_ACTN and ArduPlane:FS_LONG_ACTN are both set to 1"
I have begun setting up apm2.5, I have loaded ardupilot 2.74b.Transmitter is 9xr with dragon link. I have calibrated receiver, been thru bind process . Set elimits to on, set channel 3 (throttle) to -125% , calbrated radio and it show pwm of 910 on…
"we are currently flying with dragon link 433mhz radio system and I have a number of long range flights at 350-400 foot altitude , the longest have been 3.7 miles and 4 miles to turn around on 8000mah pack
Even assuming the video is edited the…"
Even assuming the video is edited the…"
"I think the biggest improvement that could be made would be a switch to a more conventional user friendly directory/forum structure so we could find our away around the various forums. Go to the forum page of the group mentioned in your title,…"
"I am a little confused, dev team ask for feedback on autotune, here is a log from a crash during autotune , anybody?"
"could you guys look at my log in this thread and let me know if anything major stands out .
I have had the same quad drop at the same point during the auto-tune routine 2 days in a row and the pile of destroyed motors and carbon fibre is growing.…"
I have had the same quad drop at the same point during the auto-tune routine 2 days in a row and the pile of destroyed motors and carbon fibre is growing.…"
