We have been testing APM with dual-navigation system, and it has yield positive results so far. iUAS made lot of changes away from the conventional design, so far liking this prototype. There are a few more adjustments to make, but close to product
Read more…Hi All,
I had a medium bad crash today while in the middle of validating flying modes and functions.
I was verifying guided mode from a tablet without RC xmitter on did one flight perfectly of about 2-3 minutes.
GPS was missing the landing spot
Read more…Hi DIY community, I'm working on a HackHD camera Gimble and need your advices.
The atitude metrics will be received via MavLink messages. Like MinimOSD do.
What should be the MavLink messages to listen to in order to trigger a photo or start the video?
Read more…We want to invite you to our 11 vo meeting RC pilots in Mar del Plata, Buenos Aires Argentine., if someone is near here during 4 and 5 april, visit us, free entry
Hey guys!
How are you all? I am brand new to the RC world and I am going to be asking a lot of questions ;-)
Hopefully I can share my experiences as well and everybody wins!
So first, I am trying to bind my receiver to the transmitter for the first time
Read more…Hi
I have a Pixhawk on a 3DR DIY Kit Quad and it flies well in all autonomous regimes except:
It will not automatically land after a mission if there is a land command in the mission. I have to click "land" on mission planner for it to do so.
It will ta
Read more…This was the first fly of my baby, it was my first build, I like it because it's very strong and allows me to learn without crash damages, and a great code that support all design errors, but now I'm on a second stage, I learn somethings and now I wa
Hello, today i was really happy when I receive my Pixhawk. But have a problem with installing of firmware(Adruplane 3.2.3) using Mission Planner(1.3.19)
I have the PixHawk connected via the USB cable. It seems to work. Follow all instruction, but all
I was looking at joingin https://www.skycatch.com/workmode and was wondering if anyone else has done any work through this system?
Cheers,
Todd
Read more…Hi. Help please. I am setting up a Crius AIOP v2. I ran the arduino configuration for Megapirate. It is plugged into Mission planner and the horizon is inverted. When I tilt the board it settles back into this same position regardless of how it is ti
Read more…Hi all,
High hopes dashed this evening probably through my own stupidity but I would welcome a diagnosis of the attached log, please.
This is a Tarot 250 mini quad with APM Mini 3.1 and 6M gps. All seems good, took off about 3 feet and kept her fairly
Read more…We are currently carrying DJI Phantom, DJI Inspire and parts for all at www.droneshopcanada.ca We are in the process of getting some Team Blacksheep Gear, probably sticking to multirotors for now like the TBS Discovery and Gemini, but can special ord
Read more…I see that there is a 400MW version available. Has anyone tried this one?
.
Read more…
Me and a friend have have built a 200mm diagonal quad design for fun/acro/fpv as refreshing change to big multis :).
My previous nutter quad was a 300mm ecks with KK that I had set reasonably aggro in acro.
I have seen Rob Lefebvre say the limit is 10
Read more…Using the link status in mission planner reveals that my connection is very poor. RSSI is around 200 with very little noise. The radios appear to connect fine and data does flow between the pixhawk and GCS, but the link stats shows that 4/5 packets
Read more…Ive been trying to diagnose some altitude hold problems and I think im making progress. I had a lot of vibrations using kyosho gel and it was causing my altitude hold to freak out and make extreme climbs sometimes. I moved to an "earplug" setup and s
Read more…I have been using a RFD900 on the ground and several different 3DR 915 radios in the air for some time with no issues. I recently purchased a V2 radio set from ebay. It talks to all my 3DR radios but not to either of my two RFD900 radios. All have th
Read more…Is there a way to create a mission in Tower, export that mission and load it in mission planner? I want to see the breakdown of the structure scan mission in mission planner. Thanks
Read more…Hi!
Does anyone know of an enclosure that will fit on the 3DR Y6? It would give it a more clean/polished look.
Read more…