Hello
today I set my first gimbal (pan/tilt) to my DIY quad with APM 2.6
It was flying beautiful before modifications for FPV and now I encountered some problems, first of all my Power module has gone.
My setup was no JP1 and Power module to give power
Read more…Hi All,
Can anyone provide information or a link to a resource regarding the time stamps on PixHawk dataflash logs? I can't seem to find any up to date information on all the values recorded.
Specific example:
I have a row in a log where the first row h
Read more…hi guys.. i'm a total noob, i have a QR x350pro with dvof12e radio... no ground station and no bluetooth or any other way to com with the quad other than the radio controller
i thought i read in one the the 100's of posts i've been over this month tha
Read more…Hi all,
I'm building a Tarot 250 mini quad and I've spent hours this evening trying to get Arducopter 3.2.1 to work without success.. 3.1 works fine but when I load 3.2.1 the accelerometer calibration fails (doesn't get past the first setting) and no
Read more…Hello,
So i'm having a weird problem with Taranis, dragonlink, ppm, or pixhawk I'm not sure really what it is.
I'm using a Taranis controller, dragonlinlink TX/RX PPM to pixhawk. My quad flies great, tested in all modes. all channels operate correctly
Read more…Hi guys,
I cloned from GIT the latest available ardupilot, as I intend to use the Coax firmware
I am having the following error msg :
Binary sketch size: 269 078 bytes (of a 258 048 byte maximum)
processing.app.debug.RunnerException: Sketch too big; se
(Pasay City, Philippines) - The Civil Aviation Authority of the Philippines (CAAP) recently opened its doors to a “UAV Industry Stakeholder” Conference with various Philippine Unmanned Aerial Vehicle (UAV) operators, as well as the Philippine Remote
Read more…I want to measure volt only because if using Attopilot or power module.You have to let all
the power go throw a shunt resistor if it break(no connection) you have no power and the copter
goes down.... Or have i miss understand the function?Any way if I
Read more…Hi to all,
Plan to purchase a 3DR/X8+ soon and would like to talk with members located in the Pacific Northwest that has experience with the multi-rotor. Live in eastern WA but willing to travel to Seattle/Spokane areas for conversation.
Specifically i
Read more…Hey guys,
I am following the procedure here :
http://firmware.diydrones.com/Tools/Arduino/How%20to%20Build%20Ardupilot%20with%20Arduino.pdf
Problem : the "MHV AVR Tools" download link seems to be obsolete
http://firmware.diydrones.com/Tools/Arduino/MHV_A
Read more…Hi all
Is there supposed to be a voltage on the signal wire of the ADC port?
I've installed a SF02 on my plane and it works perfectly if I monitor the output analogue voltage. However, I'm getting nonsensical values on the pixhawk when viewing the rang
Read more…Hi all,
Since moving to high-end motors and props I have had very low vibes in all my craft, so I was surprised to run into vibration issues in a recent build, my first X8. I did all the usual things of (re)checking all my motors and props for balanc
Read more…Hi,
I have newbie using pixhawk. My pixhawk was burned out due to one of my servo for camera trigger (rc10) was sucked on the camera while booting.
I have open and have a look inside pixhawk board and I found two spots that not normal on the board, ple
Read more…I'm trying to compile the ArduCopter code for an APM2 on Debian linux 7. I followed the instructions on the DIYDrones page, but the resulting ArduCopter.hex file is around 730k (found in /tmp/ArduCopter.build), which is almost double what it should
Read more…We've just flown with a multistar 10,000 and it flew very well. Gave us all 10,000 mA at 6S at 5 amps. 1hour and 15 in the air.
When we went to charge it at 5 amps, we killed two I charger 208Bs and then blew up the power supply.
Something's not right.
Read more…What will happen to a multirotor when baro glitch occurs considering there is no GPS attached?
Read more…I'm currently working on a project where I need an APM2 to send its status data (RC inputs, attitude & IMU data, etc) to a beaglebone over serial connection. My question is, how do I get the APM to send that data over mavlink, and then have the beagl
Read more…I got a problem with a 3DRobotics X8 with APM 2.6 and firmware 3.2.1 with 3DRobotics X8 RTF parameters.
When arming, its motors idles up and runs at a comfortable low idle speed, as it should.
When raising the throttle, you expect the rpms to raise as
Read more…Hi,
we are working on 3d printable airplane project to help the community.
we planned to make airplane less than 1kg to reduce 3d printing cost.
features will be pixhawk autopilot, polaroid cube HD camera, Odroid C1 for image processing purposes, and ai
Read more…Hi,
I currently have an 3DR ArduCopter Quad C Frame (https://store.3drobotics.com/products/3dr-arducopter-quad-c-frame-kit-1), now I want to buy autopilot hardware, is this frame can be used with Pixhawk?
Thank you in advance.
Read more…