Hello, I'm picking a list of parts to build an endurance big rig quadcopter. The idea is to lift a Sony A6000 for mapping (nadir, no gimbal). What are your suggestions on my build?
DAYA H4 680 (FPVmodel)
T-Motor 3508 380KV (GetFPV, but currently out of
Hello all,
I have a FLIR Vue Pro and are trying to mount it on the M600 we already had in house while maintaining the capability to shoot photos with a DJI camera. I purchased the Tarot FLIR gimbal to mount the camera to the drone. The goal is to cont
Read more…Hi,
I wanted to know if someone has tried an indoor localisation for Ardurover the way it has been done for Arducopter here:
http://ardupilot.org/copter/docs/common-pozyx.html
If yes, then can you please guide me as to what extra changes I need to do ?
Read more…I'm trying to use my pixhawk autopilot to forward a custom mavlink message from the GCS to an arduino, which will then decode the message and forward it to a transponder.
I want to be able to update this message from the GCS software while the UAV is
Read more…Hi, who have bought GPS RTK XL ("Drotek")?
I purchase GPS RTK XL ("Drotek"). And I want to contact "Drotek", but they don't receive mail.
Anyone know how to contact Drotek?
Read more…it's up to 3KM distance and combined with data and image link over WIFI 5GHz. please post your question here, we can discuss more.
Read more…To connect a N1 OSD to the Ilook+ do the following:
Take back off the Ilook+ and remove the circuit board connected to the lens (just 2 screws)
Unplug the 6 pin Jst Sh connector from the circuit board.
Cut the red wire at position 1 on the connector, th
Read more…we completed image transmission solution over WIFI 5GHz or 2.4GHz, it's up to 3Km distance with image and data link combination over WIFI, which compared to DJI WIFI solution.
Read more…When I arm the Pixhawk and the LED on the GPS module goes from flashing blue to solid blue, the motors should start spinning, however they don't. Initially i thought this would be due to improperly calibrated ESCs, but after recalibrating the error p
Read more…i want to build a agriculture drone.....the payload of the drone min:5kg.......max:10kg.....
My problems :
1. I realy dont know which is the most effecieng multirotor desiegn for a Agriculture drone... maby double sided quad or tricopter
2. I dont know
Read more…Hi all,
I'm running some tests using the SITL framework in ArduCopter, and injecting in faults to the GPS, barometer etc. For analysis, I need to get the simulation data about the position, altitude, vx, vy, vz etc. as the GLOBAL_POSITION message data
Read more…Hi,
I wanted to know if someone has tried an indoor localisation for Ardurover the way it has been done for Arducopter here:
http://ardupilot.org/copter/docs/common-pozyx.html
If yes, then can you please guide me as to what extra changes I need to do ?
Read more…I'm feeding RMC and GGA messages to ArduPilot (via GPS2), and I have a good solid RTK-Fix but ArduPilot is displaying 3D-Fix instead of RTK-Float or RTK-Fix.
I can see that Fix Quality is correct in the GGA message going to ArduPilot.
Is there a bug in
Read more…Good evening guys, I have what is more than likely a very novice question, but after many hours of searching online and not finding an answer I have decided to come here and ask.
So I read a post that said the Erle Brain was sbus compatible so I purc
Read more…Good day all
I have completed my F450 copter with a pixhawk 2.4.8 a month or so ago.
Setup :
F450
pixhawk 2.4.8
APM copter 3.5.5
R_XSR receiver
BL-Heli 32 ESC ( 40 A)
All went well and I completed all the tests : i.e. waypoint flights, RTL, failsafes...
all o
Read more…Hello all
I am trying to get hold of Joseph Douglas
Does anyone have a contact for me?
Read more…Hey there guys,
I've been asked a few times about how RTH works. I know many of you already know.
But I've been surprised lately to find some very cheap drones with better GPS functionality than more expensive ones. I mean $60 GPS drones cheap.
I have
Read more…Two months ago I started this project and had issues calibrating my Taranis X9D with my PixHawk 2.1. I'm now back giving it another go and I am still having the same issue. Here are the steps I have gone through and I have also attached images of the
Read more…