Dear
i am a beginner and want to make my own quad copter . and there i need your help i need to know that i have 2s lipo batttrey with 4 simonk 30A ESC BEC and flysky transmitter/reciever APM 2.8 with power module . now i connect my apm through power
Read more…Hiii Guys I have problem for power module calibration: I have calibration Values but that is for 6S battery but I m using 12 S batter how can I calibrate or calculate values...? if anybody help me I will be very pleasure
have Nice Day...
Read more…Hi All,
I am new to this. Can someone please forward me a parameters file that I can use to manually fly my S1000 with an onboard pixhawk, the cube and a Spektrum DX8 radio?
I am attaching my current param file, but am noticing a number of inconsistenc
Read more…Hi, In my APM 2.8 whenever I try to connect to QGroundControl through USB or through telemetry, it's directly going to Armed state, so I'm not able to calibrate or change settings. I tried QGC in windows, linux and mac. Please help
Read more…I built a Quadplane based on the Fx-79 delta wing. In QHOVER mode it takes off and flies pretty well, but when the transition to fixed-wing finishes the plane starts to oscillate pitch increasingly (I have to come back to QHOVER mode to avoid crashin
Read more…Hi
I own a couple of highly precise Fiber optic gyros and i was hoping i could try and put them to use but before this since i have no idea of how to actually wire them and how to read the information off them i was wondering if there is anyone here i
Read more…Although I believe there is no option to change motor spin direction in Mission Planner, can I simply first use the SERVO1_REVERSE parameter (or whichever numbers are appropriate) to do this, save my settings, and then run Mission Planner setup?
I nee
Read more…Hi,
I'm currently working on a multirotor solution for carrying heavy weight payload (about 15-20 kg).
I'm looking for a frame that would support my multirotor design, the whole thing should weigh up to 40 kg (perhaps 50 kg in the future).
The only requ
Hello all,
I have recently purchased a Ping2020 ADS-B transceiver. I have set it up right now with Pixhawk and it shows that it is transmitting and receiving. However, when I look at mission planner I only see aircraft around the Chicago region (flyin
Read more…Hi,
I'm kind of new to UAVs, so sorry if I make some stupid questions. Looking for a cheaper way for an antenna tracker, I found some interesting info on DIY Drones, but still do not understand some details.
Moving the trims in MP, the servos connected
Read more…Hi!
I would like to know the best workflow and flight planning that is required for conducting thermal inspections in solar plants.
Would you guys suggest taking thermal geotagged images with good overlap % and stitching it using softwares like pix4D,
Read more…Hi Folks
I am new to flight controllers, so hopefully, this difficulty is just lack of experience.
I am setting up a Pixhawk 2.1 in a fuel powered traditional helicopter.
Ardupilot - Traditional Helicopter - Preflight Testing, last point says (for stabi
Read more…Hi guys, I'm looking at putting together a high-speed Drone for heavy lifting, the point is getting 200km/h while being able to carry a weight of 15kg to 23kg with high speed, any airframe/motors suggestions?, Thanks in advance.
cheers
Read more…So I'm using mission planner 1.3.48 Im building a Rover platform.
i had to use an older build version because this was the earliest build I could find that supported the rover.
My build is a converted Traxxas Sledge Hammer an a PX4 that I stripped from
Read more…Hi everyone,
I hope I am posting this question to right place. I am working on a research project involving autonomous airships, and was looking for a reliable supplier of blimps in the UK.
Does anyone have any recommendations?
The blimp is meant to be
Read more…I have tried hooking the transmitter up to each of these areas and it just isnt getting any power when i plugg in usb or battery. I am trying to install via ibus since that is what all the cool kids do.
Hello,I've been thinking about building my first hexcopter drone and was wondering if i have selected the correct parts to assist with building it. I will need for it to be able to lift around 15lbs and have a flight time of 20 to 30 minutes. Primari
Read more…Hi everyone,
Does anyone here still uses the X-UAV Talon aircraft? Not the mini (or maxi?). I am currently building one but I am unsure of how much movement I should have on the control surfaces. I am most concerned about the V-tail (or elevator movem
Read more…