I have make a drone, and I have a problem now.
My drone sometimes rotates along z-direction, I think yaw angle is incorrect when it fly. I check yaw angle and find it is affected by motor. When I change my motors' speed, yaw angle also be changed abo
Read more…Hi, this is my first post here. I was directed here by a member on another forum. I just saw a 3DR X8+ come up for sale on a local forum and was wondering what a fair price would be of if it is worth bothering with since 3DR is not in the drone busi
Read more…I have an mRo (mRobotics) pixhawk that I’ve setup but cannot get SBUS working with my frsky X8R and wanted to see if I can solicit some ideas.
Here’s what I’ve tried
Can successfully bind X8R to Taranis and confirm I can get telemetry back from RX
RX ge
Read more…Hi guys I'm testing a hex, with a wheelbase of of 1610mm, 30 inch props, pixhawk1. I am using Lightware SF11, and IRLock for loiter, u-blox GPS.
I have tested this drone with loiter mode, and the first time it was flyable, without any issues. That was
Read more…Hi everyone.
now im making a parachute for a drone(especially for industrial) for my univ. project.
So, i'd like to ask your opinions (if you have ever used the drone parachute)
This is a simple survey\
If you don't mind, could you plz answer it?
It only
Read more…I'm building device that will move on water. Key thing is that device should keep setup direction (heading) steady whatever waves will move device up and down, tilt or even flip over.
There will be one motor propelling device and two motors - left, r
Read more…Learning Drone Hovering Application
Just Joined...so I don't know where to put this drone application/use question.
I would like this Drone to move JUST over my property at about 20 feet in the air, and move around this 100 by 200 ft. area... by itse
Read more…Hello everyone
I have build a APM 2.5 quad copter so that i can do AUTO missions. But for some reason it completely does not listen to my mission and just randomly starts flying to somewhere. Even when i run the same mission twice it will fly the one
Read more…Hello,
I am currently trying to establish a UDP connection via Wi-Fi using an ESP8266 development board.
I am able to flash the software using the NodeMCU flasher, and am able to generate the PixRacer WiFi signal from the firmware and am able to connec
Read more…hi guys,
I'm a complete beginner with drones, so please forgive me for my basic questions.
But I've been given a project to connect an intel nuc to a dji-s900. Everything seems to work well, except that when I try to connect using mavproxy:
mavproxy.py
Read more…I need an inexpensive camera that can capture at 60 fps equivalent, or even better, 120.
Resolution can be as low as 320x240 and video can be in grayscale.
Something in the price range of Eachine 1000TVL but faster (in cost of resolution) would be perf
Read more…I am new to flight controllers. Is there a way to implement my controller for attitude control of a quadcopter using pixhawk?
Read more…Hi,
This is my first time I have been using a drone. I'm using a quadcopter with a pixhawk running PX4 firmware. I'm testing my drone without props connected to a power supply. When I increase the throttle the motors start spinning normally but when I
Read more…Hi guys
I would like to model a hexarotor on simulink but i have some problems about the thrust factor b, drag factor d and the rotor inertia on x,y and z. i don't know how to calculate them and i need them all to model the effects of thrust, drag in
Read more…Hello,
I have been debating whether or not to get a 3dr telemetry setup. What are the benefits, I have an OSD so I can get quite a bit of information there, just wondering if it's a "must have" or not,
Thanks,
Barry
Read more…Hello,
I am using Pixhawk 4.2.8 Autopilot with Mission planner software. I tried to do the battery calibration as per the documents information. But it is not working for me.
Vehicle specification
Vehicle - Fixed wing UAV
Battery - 3s 2700mAh
Software -
Read more…Hello,
I am using Pixhawk 4.2.8 for my arduplane. I am using mission planner software. I just checked on how to check the data logs on maps. I got a way to check it on Google Earth. Now, what happens is, I loaded the kmz or kml file/ double clicked t
Read more…Dear friends,We purchased a Hmf U580 drone with Pixhawk FC . Everything seems fine after setting up and we are got getting any error from Mission planer or from Qgroundcontrol ( we tested on both platforms ) .But when i try to list the drone up , it
Read more…Firstly let me say that I know what I am doing is perverse but I got here by accident. I feel like I'm close but the STORM32 setup is proving tricky.
My gimbal:
It's actually a 2 axis Tarot servo gimbal but I can't control continuous servos from a Pixh
We have progress. We have not yet decided what we will do next, integrate full CANFestival - CANOpen or use the CAN driver from @EShamaev https://youtu.be/7-TG8SYGsUo
Read more…