All Discussions (33327)
Sort by
ZenMuse H3-3d "angled" one side
Hi folks,
I've a little problem with my ZenMuse H3-3D mounted on a F550 with Naza-V2.
since a couple of weeks I found out that my videos are 5 degrees angled on one side.
Everything seems ok, and it never crashed or took any hurt.Someone can help me
Need help with ESCs
Hey all,
I've been working on my first DIY quadcopter and I have pretty much everything in order so far except that I can't get my motors to turn on! I'm using a custom Arduino flight controller running MultiWii and I'm able to get the gyro/accel
Read more…Load a KML into Qgroundcontrol
Hey everyone,
I am new to QGC and was wondering if I could load a KML layer into it. I need this layer for display purposes only.
Is there any way to do it?
Thanks
Ben
Read more…Disabled veteran with a patent pending drone system needs YOUR help please.
I hope some of you will help me, I see many posts where nobody gets help or advice. I am putting together a prototype quad for a system i am developing for law enforcement. I have been desig ing for a long time and its time to compile a list of compo
Read more…Help choosing a budget flight controller
Hey everyone! I'm in the process of building what will (hopefully) become my first fully autonomous quad copter based around the DJI f450 flame-wheel. I could really do with some help choosing the flight controller and I'm hoping someone here will be
Read more…Double GPS Antenna foy yaw and RTK
Rencently I use a Chinese GPS board it has two Antennas,so it can out put for yaw data,since use we usually use compass for yaw I want use the GPS output heading instead of it,my method is change here library/AP_AHRS/AP_AHRS_NavEKF.cpp,update_
Read more…apm 2.8 dataflash
I recently purchased an apm2.8. When I go to read the logs, missionplanner tells me that there is no "dataflash inserted". Is it disabled by default? How do you activate it?
I try to set the variable LOG_BITMASK to 958 and it is impossible. Every time
Read more…Splittting Elevon PWM to seperate elevator and aileron PWM
Hello guys,
Excited from what at the pixhawk eflite convergence firmware has to offer, was wondering if it is possible mechanically (pcb/pwm splitter) or through a few lines of code possible to decouple the PWM signal that goes into the elevon, in ord
Read more…Faulty binding between pixhawk and motors
Hello guys, i crashed my hexacopter one week ago, so i decided to take it appart and use what is left to build a quadcoptere with the same components; same flight controller (pixhawk), same motors (620kv), same ESC ( hobbywing 40A) and same transmitt
Read more…Interested to make a drone payload box that can take open and close commands?
I am a researcher from dav.network
We are looking to engage with developer communities around for various projects.
If you are a developer interested in earning some compensation and DAV tokens with the skills to produce a drone payload box which can t
Read more…Flight Controller for 2.5m Octocopter
Hi,I have started a build of a 2.5m Octocopter.One of the many difficulties lies with the flight controller, as the ones I have seen are sometimes limited in size, presumably because of the PID algorithms.Does anybody know or have experience to recom
Read more…motor stop spinning
Recently i have a bought naze 32 rev6. i was able to write the cleanflight os also.
I am using A2212 1400KV brushless dc motor(4 pieces)
30A ESC bought from ebay (4 pieces)
10x4.5 propellers ( 2 pair)
Battery 1100mAh, 30C (1 piece)
Without connecting pr
Read more…coupling detection equipment
Dear drone colleagues,
A few months ago, I bought a DJI F550. I’m mainly interested in telemetry and try to couple detection equipment to this drone. I searched on the internet and noticed all kinds of sensors are available but they are mainly aviat
Read more…Minimum memory footprint required by RTKLIB?
Is it possible to port RTKLIB on micro-controllers like a 216MHz STM32 (STM32F777II) with 2MB flash and 512Kbyte of RAM?
How much minimum memory footprint is required by RTKLIB? Are there any minimum requirements on the processing power as well?
Read more…Pixhawk strange behaviour during ESC calibration
Hey!
i’ve built drone and based it on Pixhawk. Everything seems ok, escept ESC calibration process.
Im doig this proper way, but at the end, after power reset ESC calibration data is somehow removed.
Here is what I do:
1) TX throttle at maximum
2) ESC a
Read more…Lua and MAVlink message decode
Hello,
I would like to ask where can I find lua library to communicate by MAVlink.
In python2.X it can me easy made using pymavlink.
I found that i can generate some lua code using mavgenerate.py but as i can see it is some kind of wireshark plugin?
I h
Read more…Benewake Lidar fits drones for surveying
Here are three main LiDAR from Benewake fits drones quite well.
- CE30 is a 219g lidar for drones.
With an optimal range of 30m, it is accurate to 6cm, 132° horizontal FoV and 9° vertical FoV. Solid-state design is adopted without any mechanical rotating
Read more…Benewake Lidar-- Usefor and delicate for Drones
Benewake（www.benewake.com）is a national high-tech enterprise, with over 80 employees. The company is located in Keshi Building, Haidian district, Beijing. Benewake focuses on thesolid-state LiDAR.In 2016, the company received A+ round investment
Read more…