According to the wiki:
'If you have Sonar, the craft will stop holding position at 3 meters and drop straight down. '
Did anyone try that? How did it work? Thanks.
Read more…According to the wiki:
'If you have Sonar, the craft will stop holding position at 3 meters and drop straight down.'
What does it mean by " drop straight down"?
Did anyone try that? How did it work? Thanks.
Read more…Hi.... I'm a beginner of using the arducopter using APM 2560, all the instruction I've done,such uploding the APM 2560, calibrating ESC, RC, and the motors have started beeps as usual, but the command from RC doesn't mean for the motors such throttl
Read more…Hi Everyone:
I use a MB 1200 sonar for my arducopter. I test the sonar in CLI mode. But I observed that the sonar reading is always around 608cm when I put the arducopter on the table. After that I detach the sonar from the arducopter but maintain
Read more…Why do I keep getting "Reverse parameter missing" when I enter radio setup in the APM planner? I had planner version 1.0.98 and AC2 .50 loaded. I had it flying with .50 loaded and I went through a lot to get the reverseing to save. I went back into t
Read more…I have been wondering about this problem since i start to use APM about a year ago. After changing different airframe and motors, the behavior doesn't seems to improve. I check with a local friend who also encounter the behavior.
Behavior: Tilting le
Read more…Is the Z gyro being used for any purpose? If not, maybe it can help to improve altitude hold and stability.
Well, it is the reason we have 6DOF right? The recent addition of using the Accel Z is a good move.
Read more…I started out with a hexa kit from a spanish supplier. 950kV motors and 9x5 props. Pretty lightweight frame, approx 1,7 kg. Plenty of thrust for climb performance, or stopping a rapid descend. Unfortunately this copter got hit by a flag pole in my ba
Read more…Hi,
I just purchased a hexacopter from Jdrones.
The problem is, I am a total newbie and I have no idea how to get started.
I don't know where to connect what, how to connect everything to the battery so it gets powered, etc....
Is there like a comprehen
Read more…Please help. I accidentally cut with scissors a component @ APM (look picture).
Hello all:
I guess I qualify as a newbie in the RC space, but am a computer engineer with background in embedded controllers and various gadget projects over the years.
However, I am getting confused over ESC choices - I understand their purpose, power
Read more…Hi everyone:
Today I got a new apm and imu sheild. But I found that APM output voltage is 4.6v while input is 5.0v.
What may be the problem? I appreciate any help.
Thanks
Yucong
Read more…I have the arducopter and I bought a SkyFun FunJet to give that a try! But I'm having a problem and that's I cant load the code! Something about there's not enough room on the 1280? is the error message I get in the MP'er. So would someone be able to
Read more…Hey everyone I need some help here,
I followed the instructions in the wiki which are as follows,
This method works once you have all the ESCs connected to the power distribution board and have connected all your RC cables as
Read more…I read a post somewhere about activating the Z-axis accel. Can't find it now.
I would like to activate the Z-accel to stabilize the altitude at hover. Want to be able to demonstrate the push the copter down and it pops back up to where it was.
Could
Read more…Loaded the new MP and .50 and tried useing my JR 12X and R1221 receiver. The R1221 (12channel) wasn't recognized by the ACM. Wouldnt go through the servo setup. The receiver was bound and working well with a servo, but not with the ACM. I tried an ol
Read more…Hi All:
I had a strange problem. Today I connected the APM to RC, PDB, sonar, xbee as usual ( I am sure in the correct way). I found when I pluged in the battery those blue and red leds were only on for a short time and off after that the apm becam
Read more…So I am interested in playing with FPV, although I am paranoid that if I fly more than several hundred feet away I will lose the signal and crash. So what I am interested in is a failsafe that will automatically trigger RTH when either direction of
Read more…Trying figure out how arming sequence changed from bottom right to top right after Apm reset. After a flying, next time I powered up Apm would not start motors but green light stayed on. I reset Apm and when it armed it became to right and caused a c
Read more…
I have attached a string to the center of the top plate and hung the string from a high point. But I am afraid the plate will break. Is there a better trick for balancing the AC?
Read more…
