Gender
Male
About
Location
Almaty
Please tell us a bit about your UAV interest
copters and etc.
Activity Feed
"Nice. What about wifibroadcast support? I mean precompiled drivers for 30dbm."
"Does anyone used PX4 with 6S batteries? I'm going to put my px4 on tarot, but I still have no idea how to power px4 board. Before I was using only 3S bats."
"Does this unit compatible with PX4? As I know compass from 3drobotics not compotible without hacking."
"Good job.!!!! Like others I'd like to see how it work in sources. Did you used gstreamer with plugins for TI Omap DSP?"
"I think time to time all of us should see this pictures to remember risk of our hobby."
"Hello. Some time ago I was ordered couple of GPS+Compass. At that sort period of time these units was sold with out case. Now I'm interesting in purchasing only cases. Is it possible?
But the way I'm completely satisfied with that unit. Have no any…"
But the way I'm completely satisfied with that unit. Have no any…"
"I have a question about AHRS_GPS_GAIN parameter. While I was fling 2.9.1 someone advise to set this parameter to Zero (0).
I cant remeber who but someone told that with parameter should set 1 only for AdruPlane and for copter it should set to 0 to…"
I cant remeber who but someone told that with parameter should set 1 only for AdruPlane and for copter it should set to 0 to…"
"Hello everyone,
Yestoday a make couple of flights with v3.0. Px4- Works as expected. Everything almost perfected (maybe small woobles in loiter but i'm have used stock pids)
But with APM2.5 I've got crash. I was inspected all logs and video and…"
Yestoday a make couple of flights with v3.0. Px4- Works as expected. Everything almost perfected (maybe small woobles in loiter but i'm have used stock pids)
But with APM2.5 I've got crash. I was inspected all logs and video and…"
"Very NICE!!!! I like it. Is there any way to purchase it? I tried to folow store link on http://www.virtualrobotix.com/ but look like some tech problems on site it shows error: jtablesession::Store FailedDB function failed with error number 145Table…"
"I was tried to connect SBUS Rx to PX4IO but no success (with Arducopter). FrSky PPM-sum work nice. I think board is waiting for inverted SBUS like autoquad board and mikrocopter."
"I have tested my px4 but not on F330. It was on XAicraft hexa. All pid are stock. Here is the video.
https://www.youtube.com/watch?feature=player_embedded&v=ZgYGUB51S8w"
https://www.youtube.com/watch?feature=player_embedded&v=ZgYGUB51S8w"
"Wow. Look very nice. Waiting for flight video.
I have one question: As I know canopy mount magnets are rare earth and very strong. How is yout mag? I think i will big interference on mag from this magnets.
PS: I'm thinking abount mount my PX4 оn…"
I have one question: As I know canopy mount magnets are rare earth and very strong. How is yout mag? I think i will big interference on mag from this magnets.
PS: I'm thinking abount mount my PX4 оn…"
"Yesterday I was able to make test flight on my hexa with px4 on board. Alt-hold was perfect as a Loiter and RTL. I still have not good vibes on frame (bad motors) but two layers of moongel save me a little."
"Hello Gary Thank you for youe work on new wiki. I looks very nice.
PS: Could you post me your logs with vibes (IMU enabled) on your px4. I'd like to compare wuth mine."
PS: Could you post me your logs with vibes (IMU enabled) on your px4. I'd like to compare wuth mine."
"Very Nice!
Marco could you share yous param file? Or are you use e stock params. I tried fly on stock(on px4) but have wobbles in stab - need to tune."
Marco could you share yous param file? Or are you use e stock params. I tried fly on stock(on px4) but have wobbles in stab - need to tune."
"Hello all,
I already post in other thread but decide to repeat here.
To run hexa on PX4 I editer APC_CONFIG.h uncopment this line #define FRAME_CONFIG HEXA_FRAME
Then build firmware from sources and upload to board. Motors bars show me 6 motors and…"
I already post in other thread but decide to repeat here.
To run hexa on PX4 I editer APC_CONFIG.h uncopment this line #define FRAME_CONFIG HEXA_FRAME
Then build firmware from sources and upload to board. Motors bars show me 6 motors and…"
