Gender
Male
About
About Me:
UAV Flyer
Please tell us a bit about your UAV interest
Interested in Autonomous flight
Activity Feed
"Hi guys,
same problem for me too.
I tried searching on the forum but the search button does not work...
TNX!!
"
same problem for me too.
I tried searching on the forum but the search button does not work...
TNX!!
"
"Hi Guys,
may someone explain to me the right procedure to calibrate the airspeed sensor?
I looked in the guide but I've not found anything.
Thanks a lot!"
may someone explain to me the right procedure to calibrate the airspeed sensor?
I looked in the guide but I've not found anything.
Thanks a lot!"
"Hi Gareth,
Great job!
I'm assembling a similar arducopter (octo) following these instructions:
http://code.google.com/p/arducopter/wiki/AC2_Multi
To give a correct 3 degree rotation are you looking the motors from inside or outside?
Thanks a lot.
…"
Great job!
I'm assembling a similar arducopter (octo) following these instructions:
http://code.google.com/p/arducopter/wiki/AC2_Multi
To give a correct 3 degree rotation are you looking the motors from inside or outside?
Thanks a lot.
…"
"Hi Michael,
may you give me please some information about antenna tracker settings?(CTRL-F)
Thanks a lot!"
may you give me please some information about antenna tracker settings?(CTRL-F)
Thanks a lot!"
"Sorry for spamming this forum but I wish update you with some other tests.
I've loaded the firmware 2.28 with Arduino (not using MP) and the board start and work fine.
I've done 20 reboots, no problem at all.
So, I've reloaded the 2.28 with MP, the…"
I've loaded the firmware 2.28 with Arduino (not using MP) and the board start and work fine.
I've done 20 reboots, no problem at all.
So, I've reloaded the 2.28 with MP, the…"
"Hi,
after some test I've discovered to have the same issue.
The board stop loading on INIT GYRO, after that the board stop respond.
The only way to boot is to press reset switch.
Bad board?"
after some test I've discovered to have the same issue.
The board stop loading on INIT GYRO, after that the board stop respond.
The only way to boot is to press reset switch.
Bad board?"
"UPDATE
HI, the problem is still here.
After a day of configuration I've again the same problem, when I power on the board only Blue LED ON.
In debug windows It STOP load on: INIT GYRO.
After that message the board do not output any message. If…"
HI, the problem is still here.
After a day of configuration I've again the same problem, when I power on the board only Blue LED ON.
In debug windows It STOP load on: INIT GYRO.
After that message the board do not output any message. If…"
"SOLVED
After a really fast contact by support, the problem is solved.
The solution is very simple, the problem are some data in the EPROM.
Try to boot the APM2 without SDCARD, if it boot fine you have only to wipe the EPROM using the cli with…"
After a really fast contact by support, the problem is solved.
The solution is very simple, the problem are some data in the EPROM.
Try to boot the APM2 without SDCARD, if it boot fine you have only to wipe the EPROM using the cli with…"
"Same Issue for me too.
Only blue led will power on and stay solid.
To boot the APM2 I've to press the reset switch or power it by USB cable.
I've no xbee connected, only APM2 and 5V on output rail."
Only blue led will power on and stay solid.
To boot the APM2 I've to press the reset switch or power it by USB cable.
I've no xbee connected, only APM2 and 5V on output rail."
"Hi Karsten
thanks for the pictures, I'm trying to configure two XRF modules as you suggest, but the connection between APM and Mission planner stop work after some seconds. In the debug windows I've a lot of crc errors.
Do you have modified the…"
thanks for the pictures, I'm trying to configure two XRF modules as you suggest, but the connection between APM and Mission planner stop work after some seconds. In the debug windows I've a lot of crc errors.
Do you have modified the…"
"Hi Karsten,
I'm trying two XRF modules,
When I try to connect APM it start to get param list but do not complete the operation.
In the debug windows I've a lot of crc errors.
I've, like you suggested, setup the packet size to 140.
Do I've to setup…"
I'm trying two XRF modules,
When I try to connect APM it start to get param list but do not complete the operation.
In the debug windows I've a lot of crc errors.
I've, like you suggested, setup the packet size to 140.
Do I've to setup…"
"Hi,
has anyone tested this one?
http://www.rfm.com/products/spec_sheet.php?record=DNT900C
It is like a Xbee module but it cost only 69$ (or 70euro) and is 1W power.
BYE!"
has anyone tested this one?
http://www.rfm.com/products/spec_sheet.php?record=DNT900C
It is like a Xbee module but it cost only 69$ (or 70euro) and is 1W power.
BYE!"
"Hi Luca,
Simply download this Utility to setup your xbee for the right speed (56k)
http://ftp1.digi.com/support/utilities/40003002_B.exe
Bye!"
Simply download this Utility to setup your xbee for the right speed (56k)
http://ftp1.digi.com/support/utilities/40003002_B.exe
Bye!"
Hi All, There is a way to loiter until a specific altitude is reached? I wish to program a mission for an AutoLanding that start from a specific altitude to begin a correct landing circuit. Thanks a Lot, here is my last…
Hi all, today I've loaded the new 2.26 version.The first flight is OK, but when I 've tried to restart the APM it won't boot. I've tried to connect to it by USB port and moving the switch I've done a reset by the CLI.The reset was ok, but nothing to…
"Hi Darren, thanks a lot,
do you have any documentation about the pan/tilt servos connections?
and how i can connect the 1280 to the HK?
What I think is that I wish to use APM Mission Planner connected with the Xbee to my plane and have an…"
do you have any documentation about the pan/tilt servos connections?
and how i can connect the 1280 to the HK?
What I think is that I wish to use APM Mission Planner connected with the Xbee to my plane and have an…"
