About

Gender

Male


Location

Ribeirao Preto, SP


About Me:

What about me? :)


Please tell us a bit about your UAV interest

I'm just starting with UAV's.


Hometown:

Ribeirao Preto


Activity Feed

Jonis Maurin Ceara commented on Andreas M. Antonopoulos's blog post ArduCopter 2.7 Released!
"I can't get my camera servos to work :(  APM 2560 + fw 2.7"
Jul 26, 2012
Jonis Maurin Ceara commented on Chris Anderson's blog post APM: the Universal Autopilot
"That's a great software! Te only problem that i can see is that is made for windows! For us (Mac users) it's su!#s to have an virtual machine running only for one software (an essential software!)"
Dec 21, 2011
Jonis Maurin Ceara posted a discussion
Hi.This weekend i've changed my hexa from X to +....everything was fine, i was flying good with a lot of wind....but, on landing, my hexa fliped.Result: 2 motor-mount broken. I've made 6 new aluminium replacements and installed. After that, doing…
Nov 21, 2011
Jonis Maurin Ceara replied to George Khobra's discussion Arducopter crash in loiter mode
"My first copter it's an hex a from jdrones. I had no problem at all, except some oscillations on high winds....but no problem at all. Just take off, flight and land again. After that, I've installed the sonar (already with shielded cable and LPF)…"
Nov 17, 2011
Jonis Maurin Ceara replied to Marianne Antonio's discussion APM Mission Planner Open Source?
"Chris, to not open a new thread, i'll ask here: MAVLink use any kind of encoding? I'm asking because i'm planing to build my own mission planner (open-source too), but i'll write in lazarus so we (MAC users) can use without any VM.
I readed some…"
Nov 8, 2011
Jonis Maurin Ceara posted a discussion
Hi.I need to change my RATE_PIT_P and RATE_ROLL_P, but i can 't do it in mission planner anymore.I saw in another topic that i must change to CLI mode (swtich), but doing this i can't load params and change.....also, this error happen only with…
Nov 6, 2011
Jonis Maurin Ceara replied to Jason Short's discussion Arducopter 2.0.48/49
"Jason, is there any way to change Rate P settings wthout manually upload firmware using Arduino (in version 2.0.49)? 
Mine is working almost fine and i just need some tweeks, i don't want to upload firmware again.
Question 2: i saw in wiki that i…"
Oct 26, 2011
Jonis Maurin Ceara replied to Greg's discussion Sonar Noise Reduction update
"I'm not using this filter, only a shielded cable and 3 ferrites inline. This is my test for about 5 minutes holding my hexa (with props and motors running) on my room, solid ground and changing some centimeters after 2 minutes, then 1, etc...
I…"
Oct 25, 2011
Jonis Maurin Ceara replied to Jonis Maurin Ceara's discussion PID for 'original' hexa
"Flight video:"
Oct 22, 2011
Jonis Maurin Ceara posted a discussion
Hi. This is my first multirotor and it's almost perfect.I've made maiden flight today and my hexa (from jdrones) is oscilating a little bit (faster). It's almost when windy (a little, too). I'll post a video soon, but reading wiki, i saw that i must…
Oct 22, 2011
Jonis Maurin Ceara replied to Jonis Maurin Ceara's discussion How to get my magnetic declination?
"It's normal that mission planner remove the DOT after change tab?
I've inserted "-20.21" and after change that and go back, i see "-2021". Is that right?
 "
Oct 21, 2011
Jonis Maurin Ceara replied to Tomas Soedergren's discussion Unable to enter values in Planner/Config/Setup/Battery tab in ArduCopter User Group
"Since the scale output is up to 3.3V and APM analog input takes up to 5V, i would connect this sensor without any resistor.
In this case, you'll lose some reslotuion, since APM expect 5V (max) on analog....unless there's a way to change reference…"
Oct 21, 2011
Jonis Maurin Ceara replied to Jonis Maurin Ceara's discussion How to get my magnetic declination?
"Tks guys, i'll try to liftoff tomorrow! :D
 "
Oct 20, 2011
Jonis Maurin Ceara posted a discussion
Hi!First of all, that's my first post and first multi-rotor (DIY Drones hexa). I have my hexa almost done and i'm testing sensors and finishing build. The thing is that magnetic-declination site is offline and i don't know how to get my magnetic…
Oct 20, 2011
Jonis Maurin Ceara commented on Gordon's blog post Mode Switch Setup
"no problem....lol.....tks :)"
Oct 4, 2011
Jonis Maurin Ceara commented on Gordon's blog post Mode Switch Setup
"Gordon, another idea is to export your model with this mix setup and share with us! :)
It's easy and you just need an SD card. 
 
Tks for this tuto!"
Sep 30, 2011