Gender
Male
About
Location
El Cajon, CA
About Me:
Life IS Good
Please tell us a bit about your UAV interest
Heli & Quad
Activity Feed
"the last version is failing when downloading from the android store"
"Great work...
Since we have now support for 1.9 MTK firmware. I tried searching on how to upgrade the firmware but was not successful. If it is covered in another forum, would greatly appreciate the link.
TIA"
Since we have now support for 1.9 MTK firmware. I tried searching on how to upgrade the firmware but was not successful. If it is covered in another forum, would greatly appreciate the link.
TIA"
"Great features on 1.34 and is still Working on 4.0.4.
Thanks"
Thanks"
"Like the new features but I am not getting communication with the APM.
"
"
"Let me start by thanking you for a great job, I am hooked and look forward to every update...
I have a Sony S tablet and the app(latest ver) is running fine. The vehicle overview is not getting populated and the airplane icon is mostly yellow. I am…"
I have a Sony S tablet and the app(latest ver) is running fine. The vehicle overview is not getting populated and the airplane icon is mostly yellow. I am…"
"Thanks for 2.6.4 and specifically enabling support for the 1280/GPS. I loaded the new firmware and I am back in business..."
I have updated my board using the MP 1.2.9 to AP 2.60. I did not get any erros but the MP is not sensing the MTK GPS.Officialy the APM 1 is not supported and I am wondering what version of MP/AP combination I should use untill I am ready to get the…
"Same issue here. I have an APM1 and GPS was working before I upgraded to AP2.6 and MP1.2.8
I am getting a lock on the GPS (solid blue led)."
I am getting a lock on the GPS (solid blue led)."
"Same issue with the APM Planner 1.36 and the Failed to Verify Issue. I used Arduino to upload and used APM 1.36 to configure. Flew the quad and all seemed normal.
I just tried to check the logs, but was not able to see any. If you disconnect the…"
I just tried to check the logs, but was not able to see any. If you disconnect the…"
"Download site showing 2.0.25 while the APM planner upload firmware is still showing 2.0.24?
Are they in sync?
"
Are they in sync?
"
"I also order two of them, crashed the first one and now the second is ready. I've loaded the latest firmware, but I am having stability issues. If any had success flying/tuning, can you please post your PID settings."
"I have a 9303 and followed the noted instructions. When I am trying to set "MODES" with the the Gear-Aux2 switches in the defualt position- I get Pos-4: Auto but if I wait the modes start cycling for the Pos-4. I am NOT moving the Aileron so I am…"
Completed Quad:Frame: HK V1Motors: Turnigy 2213ESC: Turnigy Plush 30Elec: AMP, IMU, GPS, MagnetometerProps: 9x5Software: Arducopter 2.0.8RX: JR 921TX: JR X9303
-
Naji Karim Brandon,
I just finished watching you two videos- it looks good for first flight. You mentioned in your comments that you think leveling the frame might have help solve you initial problem. Can you share how you did that. I believe I might similar… -
Naji Karim Good to know Brandon. What did you end up getting for a frame?
-
Naji Karim The Arms do come CA'd but I went over them again since some parts were loose. With the regards to twist, I will try to take a short video of the quad with the motors running so you can judge the extent of the vibration. I did not balance the props…
-
Naji Karim Hi Mark,
The frame come half assembled. The four arms were assembled but I highly recommend that you put CA on all the points. Every thing else (landing gear, dome) need to be CA'd by you. It is not hard, and on the HK website, a user had posted…
"Hi Brian,
I might be interested in one of those four boards. I have a couple of helis 2x Trex 450s and one Trex 600 that I can use a test platform. I was a controls engineer, a while back and did also a lot of C programming again a while back. I do…"
I might be interested in one of those four boards. I have a couple of helis 2x Trex 450s and one Trex 600 that I can use a test platform. I was a controls engineer, a while back and did also a lot of C programming again a while back. I do…"
"Hi John,
I just became a member and I am very interested in the work that has been accomplished specifically for helis. I am fairly new to the hobby and have a Trex 600 & 450 and JR DSM TX/RX.
I have not done C programming over 15 yrs but probably…"
I just became a member and I am very interested in the work that has been accomplished specifically for helis. I am fairly new to the hobby and have a Trex 600 & 450 and JR DSM TX/RX.
I have not done C programming over 15 yrs but probably…"
