About

Gender

Male


Location

Moab, Utah


Please tell us a bit about your UAV interest

none


Hometown:

Moab, UT


Activity Feed

vyoufinder posted a discussion
Can anyone tell me if it is possible to control my Movi M5 gimbal using my Taranis X9D+ transmitter and X8R receiver?The Taranis X9D+ is not on the list of controllers recommended by Freefly for the Movi M5, but then I see other gadgets which can…
Apr 7, 2020
vyoufinder replied to vyoufinder's discussion Recommend a Gimbal for Flying Sony a7s & A7sii on s1000?
"I ended up going with a Movi M5, and Cinemilled mounting hardware with longer legs. The Gremsy is probably sleeker in design, but I only paid half what the Gremsy costs for this setup. Plus I can use it for larger cameras when I use them off the…"
Feb 27, 2020
vyoufinder posted a discussion
Learning about gimbals for my s1000 frame has proven to be spotty on information. Gimbals I have seen and looking at so far are; Movi M5, Gremsy T3, and DYS A7. For all three, there's barely any information I'm finding. For the Gremsy, I can't even…
Jan 19, 2020
vyoufinder replied to Dean Hitrec's discussion Attopilot 180 A, non linear voltage&current reading
"I've decided on the Mauch power module, because it claims to be more accurate and also use less power to get wasted into a resistor.  I don't know how to know which 200A module to get though.  There is  28v for 2s-4s packs, and a 60v model for…"
Nov 29, 2019
vyoufinder replied to Gremsy's discussion What Is New On Gremsy T3-V2?
"The Gremsy gimbals look good.  I am wanting to buy one, but can't seem to find out if and or how it will work with my Taranis X9d.  Can you tell me?  I've already called more than one Gremsy dealer, and written the Gremsy company.  The only example…"
Nov 27, 2019
vyoufinder replied to Cristóbal Valdivieso's discussion Attopilot 180A burn with DJI S1000
"I've read about this happening to others.  I have an s1000 that came with a burned out 90A 5v Attopilot installed.  I almost replaced with one of the same, but then I realized it and now have on order a 180A 5v Attopilot chip on order..  Reading…"
Nov 27, 2019
vyoufinder replied to vyoufinder's discussion Pixhawk1 Error Uploading Firmware no matter what I try
"vyoufinder SHOULD HAVE said:
I've solved this. For anyone else running into the issue, here is what all was required:
1.  Disconnect from Mission Planner or QGround Control.
2.  Open Task Manager and shut down all COM Surrogate ports
3.  Uninstall…"
Nov 25, 2019
vyoufinder replied to vyoufinder's discussion Pixhawk1 Error Uploading Firmware no matter what I try
"I've solved this. For anyone else running into the issue, here is what all was required:
1.  Disconnect from Mission Planner or QGround Control.
2.  Open Task Manager and shut down all COM Surrogate ports
3.  Uninstall Mission Planner
4.  Install…"
Nov 25, 2019
vyoufinder replied to vyoufinder's discussion Pixhawk1 Error Uploading Firmware no matter what I try
"Thanks.  Will do it then.  However.. I'd really like to get my COM ports working again.  Not only for Pixhawk, but I just like things to be working when I need it for the next time.. Any way to uninstall ALL COM updates from Mission Planner/firmware…"
Nov 24, 2019
vyoufinder posted discussions
Nov 24, 2019
vyoufinder replied to John Bowie's discussion Mission Planner connection issues
"Same problem.  Tried all the same and much more.. Any answers?"
Nov 24, 2019
vyoufinder replied to vyoufinder's discussion Pixhawk1 Error Uploading Firmware no matter what I try
"I was not convinced that the Pixhawk was bricked.  A quick check into my log files showed screwy looking COM port settings changed and looked like errors.  So I tried it on another computer and was able to install firmware without a problem.  I…"
Nov 24, 2019
vyoufinder replied to Piers C's discussion Formerly working Pixhawk IO board problem / now bricked? Factory reset possible?
"I had the same problem.  A brand new, perfectly working Pixhawk, first thing I did was to "upgrade" the firmware which bricked it.  In my opinion, developers should inform people before updating that Pixhawk is not compatible with the latest…"
Nov 24, 2019