Gender
Male
About
Location
Kolkata
Please tell us a bit about your UAV interest
Flying UAV s with autopilots
Hometown:
Kolkata
Activity Feed
"Hello iskess,
Does the latest version of the MP allow this? what are the parameters that need to changed to achieve that?
Secondly, I want to use 2 uav's in one GCS on the same map? is this possible? Although 2 programs on the same computer shall…"
Does the latest version of the MP allow this? what are the parameters that need to changed to achieve that?
Secondly, I want to use 2 uav's in one GCS on the same map? is this possible? Although 2 programs on the same computer shall…"
"Hey People,
What are the flight limitations of the pixhawk 2 with default computer on-board? Like attiude, rates, accelerations, resolution , speeds and pressure range?"
What are the flight limitations of the pixhawk 2 with default computer on-board? Like attiude, rates, accelerations, resolution , speeds and pressure range?"
"Hi Seppo et all,
I have been using the RFD900 and 900+ for quite some time now. I m very happy with their performance. i had made a small change to the connection configuration of the modem with pixhawk. I am externally powering the RFD900 from…"
I have been using the RFD900 and 900+ for quite some time now. I m very happy with their performance. i had made a small change to the connection configuration of the modem with pixhawk. I am externally powering the RFD900 from…"
"@Jacko: Any success with the auto takeoff feature?
My plane always tries to level after launch instead of climbing to commanded altitude of 25 metres. The motor switches ON after launch but the Elevons try and pitch down the plane instead of…"
My plane always tries to level after launch instead of climbing to commanded altitude of 25 metres. The motor switches ON after launch but the Elevons try and pitch down the plane instead of…"
"Hello to all, The model flies very well in manual mode using my transmitter and Qground control. However it loses altitude and goes into "Land" mode while i try to switch to "Auto"/"Mission" mode. TheTake off command doesn't work as well. I hope…"
"Philip, that looks awesome and that reply was blitzkrieg, Thanks
Few more questions, can we use more accurate GPS receivers directly with this? Also, what would be the required Input Voltage range?"
Few more questions, can we use more accurate GPS receivers directly with this? Also, what would be the required Input Voltage range?"
"Hey Philip,
I cannot be more excited for the upgraded Autopilot. Just a stupid question, I want to know how is it comparable with a PixHawk1 in terms of operatability and physical connections as i do not understand whether PixHawk 2 is a stand alone…"
I cannot be more excited for the upgraded Autopilot. Just a stupid question, I want to know how is it comparable with a PixHawk1 in terms of operatability and physical connections as i do not understand whether PixHawk 2 is a stand alone…"
Hi all, My setup is as follows: Pixhawk running Arduplane 3.2, RFD 900, Futaba s3005 servos on all surfaces including throttle, Gasoline engine. I have been using pixhawk along with an electric powered plane without servo issues.In the above…
"Hi everyone,
Happy new year to all!!!
I use RFD900 modem with pixhawk and i have reached 10 kms out of home position flight successfully. I had put up my Ground Antennae high to achieve that. The real issue is, on the mission planner, during the…"
Happy new year to all!!!
I use RFD900 modem with pixhawk and i have reached 10 kms out of home position flight successfully. I had put up my Ground Antennae high to achieve that. The real issue is, on the mission planner, during the…"
"Hi Pekka,
I am facing the same problem, Did u figure out what the problem was??"
I am facing the same problem, Did u figure out what the problem was??"
"Hi James,
Can you post a picture of your Base station RFD900 powered by the BEC and the data cable to USB.
I want to make sure to have done the data wiring right!!!
Cheers"
Can you post a picture of your Base station RFD900 powered by the BEC and the data cable to USB.
I want to make sure to have done the data wiring right!!!
Cheers"
"Jakub,
Thanks mate!!!
Will try it immediately and disturb u again if i have any doubts!!!
Really appreciate it. Thanks again."
Thanks mate!!!
Will try it immediately and disturb u again if i have any doubts!!!
Really appreciate it. Thanks again."
"Hi all,
Sorry to be a noob and ask this.
Started working on the tracker project from yesterday. My intended setup is:
Plane RFD900 connects wireless to ground RFD900 connected directly to GCS via USB, Antenna tracker with Pixhawk as controller board…"
Sorry to be a noob and ask this.
Started working on the tracker project from yesterday. My intended setup is:
Plane RFD900 connects wireless to ground RFD900 connected directly to GCS via USB, Antenna tracker with Pixhawk as controller board…"
"Randy,
I already read the page and the setup and configuration is alright.
Now i wan to integrate the tracker with my GCS, AV position data from GCS to my Antenna tracker (Pixhawk operated).
In the wiki, its mentioned that pixhawk should be…"
I already read the page and the setup and configuration is alright.
Now i wan to integrate the tracker with my GCS, AV position data from GCS to my Antenna tracker (Pixhawk operated).
In the wiki, its mentioned that pixhawk should be…"
"Hi Greg,
I am looking to pass my vehicles information on to the Antenna tracker (Pixhawk used as a controller board for yaw and pitch) What settings shouls i use??? or am i missing something very basic here. Would highly appreciate ur help!!!
Also i…"
I am looking to pass my vehicles information on to the Antenna tracker (Pixhawk used as a controller board for yaw and pitch) What settings shouls i use??? or am i missing something very basic here. Would highly appreciate ur help!!!
Also i…"
"Hi Randy,
I want to build a tracker with a pixhawk as the servo controller board and it would be connected via USB to my GCS and i would have my RFD900 connected via USB to the same GCS.
1. Is this the easy way? Advice on any other simple solution!!…"
I want to build a tracker with a pixhawk as the servo controller board and it would be connected via USB to my GCS and i would have my RFD900 connected via USB to the same GCS.
1. Is this the easy way? Advice on any other simple solution!!…"
