Beau
  • Male
  • United States
Share Twitter

Beau's Friends

  • Rick Steele

Beau's Discussions

PPM Channel Order for JR

Started this discussion. Last reply by Mike Feb 24. 9 Replies

I am using a JR 10sx with a Frsky module and PPM Rx.  The PPM stream that is output from the rx has the channels in the wrong order for using with the Arducopter code.  Is there a way to change the…Continue

Tags: order, change, encoder, JR, ppm

Arducopter 2.0.38 weird behavior

Started Aug 7, 2011 0 Replies

Hi everyone,I have had an Arducopter for about 2 months and I love it.  I have been progressing through the Beta firmware as it has been released and it gets better every time. However, I have had a…Continue

Beau's Groups

 

Beau's Page

Latest Activity

Mike replied to Beau's discussion PPM Channel Order for JR
"And not only is it out of order but on mine I have my rangelink hooked up through ppm on apm 2.5 and only output 4 works correctly and no other output will work a servo beside output 2 for my elevator but it can only move up and down a tiny bit and…"
Feb 24
Justin Pead replied to Beau's discussion PPM Channel Order for JR
"To my knowledge, this has not been implemented. I still fly with a wire for each channel. which is unfortunate. Regards"
Feb 24
Mike replied to Beau's discussion PPM Channel Order for JR
"I know this is a oldddd post but I have the same problem. Anyone have an answer???"
Feb 22
Beau commented on Jani Hirvinen's blog post Adding more features to IOBoard
"Nils, You know, now that I think about it, it might have been because I was not initiating communications with the 3DR radios to get the info flowing.  I had them out of the loop during some of that time cause I have them going thru an OSD…"
Oct 17, 2013
Beau commented on Jani Hirvinen's blog post Adding more features to IOBoard
"Nils, I want to thank you again for the diagram.  After getting home I had telemetry displaying on my Taranis in just a few minutes. Regards, Beau"
Oct 17, 2013
Beau commented on Jani Hirvinen's blog post Adding more features to IOBoard
"Nils, No problem, I am guilty of doing the same from time to time. Cool, that is exactly what I needed, thanks.  That shows me that I am not hooking it up correctly.  I was using the tx and rx on the end of the board where the…"
Oct 16, 2013
Beau commented on Jani Hirvinen's blog post Adding more features to IOBoard
"Nils, If the above post was a reply to me, I must point out that I am not using the X8R receiver, I am using a D8R-XP, which I know some guys are hooking straight up to the Arduino, but I can't get it to work.  Thanks for replying…"
Oct 16, 2013
Beau commented on Jani Hirvinen's blog post Adding more features to IOBoard
"Hi guys, I am trying to get telemetry displayed on my Taranis using an Arduino Mini Pro and a D8R-XP receiver.  I used Xloader to upload the .hex file onto the Arduino.  I now have a dim red LED and a slow flashing yellow LED.  I have…"
Oct 16, 2013
Beau commented on Bill Bonney's blog post Welcome to Taranis!
"I got mine about a month ago and I love it.  Programming it takes a different approach, but not difficult.  The programming possibilities are endless. I am used to a JR10SX, and this weighs nothing compared to what I am used to, but I will…"
Oct 3, 2013
Josh Potter replied to Beau's discussion PPM Channel Order for JR
"Old thread but was there ever fixed?  I'm looking to move to EZUHF or RangeLink UHF and  wanted to use PPM of course. Does re-assigning channels on your radio not change what order they show up on the APM?  (i.e. I move…"
Sep 9, 2013
Beau replied to Randy's discussion ArduCopter-3.0 ready for wider use
"Randy,   As a JR Tx and Frsky PPM Rx user I am glad to see that RCMAP is a possible new feature.  Thanks for all the great work you and the other developers are doing. Best regards,   Beau"
Jun 20, 2013
Beau replied to Hugues's discussion H frame supportes by arducopter ? in the group ArduCopter User Group
"Hugues, The arm it self doesn't matter, what matters is the location of the motor in relation to the center of gravity of the copter.  You could have an arm that is curved in all kinds of directions and the copter will not know the…"
Apr 23, 2013
Beau replied to alex corbett's discussion FRSKY PPM SETUP HELP REQUIRED PLEASE.
"Angelo, I think most people use the Arduino IDE, which you can download from here: http://arduino.cc/en/Main/Software It is a little particular about where you place the source code.  The first time you run the IDE it will place an…"
Mar 29, 2013
Beau replied to Angelo Borter's discussion how to rearrange receiver Inputs?
"Angelo, Take a look at this thread: http://diydrones.com/forum/topics/frsky-ppm-setup-help-required-please You have the same issue we have with JR tx using a FrSky Rx.  This explains how to change the code to reorder the channels.  I…"
Mar 28, 2013
Beau replied to alex corbett's discussion FRSKY PPM SETUP HELP REQUIRED PLEASE.
"I also would like to thank everyone that helped with this. Alex, I am glad to hear that works.  I haven't had a chance to try it yet, but hope to in the near future. Best regards, Beau"
Mar 19, 2013
Beau replied to alex corbett's discussion FRSKY PPM SETUP HELP REQUIRED PLEASE.
"Randy,  I figured that is what was needed, but I was afraid it might not play well with the failsafe function of the throttle.  I guess as long as the radio.pde knows which one is the throttle channel and passes the correct information to…"
Mar 7, 2013

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

Profile Information

About Me:
I am a mechanical engineer and been flying RC for 25 years.
Please tell us a bit about your UAV interest
I have an APM2 in a custom frame. I design and fabricate custom multirotor aircaft using my CNC router.
 
 
 

© 2014   Created by Chris Anderson.

Badges  |  Report an Issue  |  Terms of Service